60903
171
Zoom out
Zoom in
Previous page
1/182
Next page
Additional information
16
171
En
• The HDD has not been sufficiently
optimized. Please optimize again.
If this message appears repeatedly after optimizing the HDD it is
likely that there is not enough free space on the HDD for optimization
to complete properly. Please erase some titles from the HDD and
optimize again.
• An error occurred. Please consult the service
center. Note that contents on the HDD may be
erased when servicing this unit.
This message is displayed when information from the HDD cannot
be read. The HDD may be damaged or broken. Please ask your
nearest Pioneer-authorized service center or your dealer to carry out
repairs.
• The Hard Disk Drive info is incorrect. Use the
Disc Setup menu to reinitialize.
As the HDD info cannot be properly read, no new recordings can be
made. Reinitializing the HDD (page 148) may result in your being
able to make recording again. Note that reinitializing the HDD will
erase all recorded contents, including protected files.
• This signal’s TV system is different from the
recorder’s setting.
The TV system (PAL, NTSC, etc.) of the current channel is different
from the TV system settings of this recorder.
• Recording failed due to a TV system
mismatch. Press DISPLAY to clear message.
The timer recording failed because the TV system of the channel set
for recording was different from the setting of the recorder.
• Playback has stopped because the TV system
is different than the recording.
During recording or timer recording standby, the TV System (PAL,
NTSC, etc.) of the playback video changed, causing playback to stop
automatically.
• You are not allowed to watch this
Conditional Access Programme.
A CA module or smart card (obtained from your service provider) is
required to watch the selected programme. Insert the supplied
module or card into the Common Interface card slot on the front of
the recorder (page 17).
• There is no DV input or the input signal is
unrecordable.
No signal was detected at the DV IN jack. This may appear if a blank
section of DV tape is playing in the connected camcorder.
• No DV camcorder connected. The camcorder is not connected properly, or the camcorder is
switched off.
• You cannot connect more than one DV
camcorder at a time.
This recorder’s DV jack supports connection to just one camcorder.
• Cannot operate the DV camcorder. This recorder cannot operate the DV camcorder. Try switching off the
camcorder then turn it back on again.
• Could not operate the DV camcorder. This recorder was not able to operate the DV camcorder.
• The DV camcorder is not set for playback.
Please select playback mode on the DV
camcorder.
The camcorder is in camera mode. Switch it to playback mode.
• The printer is not ready or is not connected.
Please check the printer.
This message is displayed when communication could not be
established with the printer. See the Troubleshooting section if you do
not know the cause.
• Printing has been cancelled because ... This message is displayed when there is a printer error during
printing. After checking the printer for the cause of the error, either
reconnect the printer and start the printing job again, or select “Yes”
to resume printing (select “No” to cancel the print job). See also the
operating instructions that came with your printer for possible
causes of print errors.
Message Explanation/Action
02SDVRLX70D_EN.book 171 ページ 2008年10月9日 木曜日 午後4時38分
Downloaded from www.Manualslib.com manuals search engine
171


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer LX-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer LX-01 in the language / languages: English as an attachment in your email.

The manual is 13,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer LX-01

Pioneer LX-01 User Manual - English - 2 pages

Pioneer LX-01 User Manual - German - 179 pages

Pioneer LX-01 User Manual - German - 2 pages

Pioneer LX-01 User Manual - Dutch - 180 pages

Pioneer LX-01 User Manual - Dutch - 2 pages

Pioneer LX-01 User Manual - Danish - 179 pages

Pioneer LX-01 User Manual - French - 179 pages

Pioneer LX-01 User Manual - French - 2 pages

Pioneer LX-01 User Manual - Italian - 179 pages

Pioneer LX-01 User Manual - Italian - 2 pages

Pioneer LX-01 User Manual - Swedish - 356 pages

Pioneer LX-01 User Manual - Spanish - 179 pages

Pioneer LX-01 User Manual - Norwegian - 356 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info