60903
165
Zoom out
Zoom in
Previous page
1/182
Next page
Additional information
16
165
En
Troubleshooting
Incorrect operation is often mistaken for trouble and malfunction. If you think there is something wrong with this
component, please check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after checking the points
below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
General
Problem Remedy
Can’t eject a disc Turn off the power to this device and press and hold OPEN/CLOSE on the front of the
recorder for more than three seconds.
Can’t play a disc • Check that the disc is a compatible format disc (page 58).
• Take out the disc and clean it (page 174).
• Check that the disc is loaded properly (aligned in disc tray and label-side up).
• Check that the disc has a region code compatible with the recorder.
• Press HDD/DVD (LCD page 1) to select the DVD.
• There may be condensation in the recorder. Leave the recorder for an hour or so for the
condensation to evaporate.
• During HDD recording, you can’t play discs that are recorded with a Line System different
to the current recorder setting.
• DVD+R/+RW discs recorded using another recorder with copy-once protected recordings
will not play in this recorder.
Can’t record a disc • Check that the disc is not an incompatible format disc (page 58).
• Check that the disc is loaded properly (aligned with the disc tray with the label side facing
up).
• Remove the disc from the disc tray and clean it (page 174).
• Some DVD-RAM discs are not recordable until they have been initialized (page 102). This
can take up to an hour.
Remote control does not
work
• If you connected this recorder to the receiver subwoofer using the CONTROL IN jack, point
the remote control at the display unit of the receiver subwoofer to use (page 26).
• Use the remote within its operating range (page 26).
• Replace the batteries (page 26).
All settings are reset • If the recorder is unplugged (or there is a power failure) while the recorder is on, all the
settings will be lost.
• Make sure that you switch the recorder into standby before unplugging the power cord.
No picture Check that everything is connected properly (page 8).
• Check that the connected TV and/or the AV amp/receiver is set to the correct input.
• If you are using an indoor antenna that requires power, make sure that Aerial Power in the
Initial Setup menu is set to On or Auto (page 153).
• If the aerial/antenna is not connected properly, or if it is shorted, the Aerial Power setting
will revert to Off automatically. Check the aerial connection and try making the setting again.
No sound or sound is
distorted
• Make sure that the amp/receiver or TV is set to the correct input and the volume turned up.
• There is no sound when the picture is paused, or during scanning or slow motion play.
Press (Play)(LCD page 1) to resume regular playback.
• If the sound is distorted, try cleaning the cable plugs.
Cannot switch a bilingual
programme
• During real-time copying it is not possible to switch audio channels. The main and sub
channels are both output.
The picture from the
external input is distorted
• If the video signal from the external component is copy-protected, you cannot connect via
this recorder. Connect the component directly to your TV.
The picture is distorted • Change the Input Line System setting (page 161). (You can also change it by pressing the
(Stop) button and (Play) on the front panel simultaneously with the recorder stopped.)
02SDVRLX70D_EN.book 165 ページ 2008年10月9日 木曜日 午後4時38分
Downloaded from www.Manualslib.com manuals search engine
165


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer LX-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer LX-01 in the language / languages: English as an attachment in your email.

The manual is 13,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer LX-01

Pioneer LX-01 User Manual - English - 2 pages

Pioneer LX-01 User Manual - German - 179 pages

Pioneer LX-01 User Manual - German - 2 pages

Pioneer LX-01 User Manual - Dutch - 180 pages

Pioneer LX-01 User Manual - Dutch - 2 pages

Pioneer LX-01 User Manual - Danish - 179 pages

Pioneer LX-01 User Manual - French - 179 pages

Pioneer LX-01 User Manual - French - 2 pages

Pioneer LX-01 User Manual - Italian - 179 pages

Pioneer LX-01 User Manual - Italian - 2 pages

Pioneer LX-01 User Manual - Swedish - 356 pages

Pioneer LX-01 User Manual - Spanish - 179 pages

Pioneer LX-01 User Manual - Norwegian - 356 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info