811527
3
Zoom out
Zoom in
Previous page
1/7
Next page
Connections when using
the speaker input wire
Connect the stereo speaker output wires to
the amplifier using the supplied speaker input
wire with RCA pin cord.
1Stereo
2Speaker output
3Red: Right +
4Black: Right *
5Black: Left *
6White: Left +
7Speaker input wire with RCA pin cord
To the RCA input jack of this unit
Notes
!If speaker input wires from a headunit are
connected to this amplifier, the amplifier will
automatically turn on when the headunit is
turned on. When the headunit is turned off,
the amplifier turns off automatically. This
function may not work with some headunits.
In such cases, please use a system remote
control wire (sold separately). If multiple am-
plifiers are to be connected together synchro-
nously, connect the head unit and all
amplifiers via the system remote control wire.
!This amplifier automatically selects an input
signal mode between the RCA level and the
speaker level by detecting an input signal.
Solderless terminal
connections
!Since the wire may become loose over
time, it must be periodically inspected and
tightened as necessary.
!Do not solder or bind the ends of the
twisted wires.
!Fasten while making sure to not to clamp
the insulating sheath of the wire.
!Use the supplied hexagonal wrench to
tighten and loosen the terminal screw of
the amplifier and use it to securely fasten
the wire. Be careful to avoid excessive tigh-
tening of this screw, which may damage
the wire.
Connecting the power terminal
WARNING
If the battery wire is not securely fixed to the term-
inal using the terminal screws, there is a risk of
overheating, malfunction and injury, including
minor burns.
!Always use the recommended battery and
ground wire, which is sold separately. Con-
nect the battery wire directly to the boat
battery positive (+) terminal and the
ground wire to the boat body.
!Recommended wires size (AWG: American
Wire Gauge) is as follows. The battery wire,
the ground wire and the optional direct
ground wire must be same size.
!Use a wire of 12 AWG to 16 AWG wire for
the speaker wire.
1 Route battery wire from engine com-
partment to the boat interior.
!When drilling a cable pass-thru into a bulk
head or barrier wall, route the cable
through carefully and seal the hole to pre-
vent fumes from seeping from engine com-
partment to other areas.
<5707000012820V>9
En
Connecting the units
After completing all other amplifier connec-
tions, finally connect the battery wire terminal
of the amplifier to the positive +battery term-
inal.
2
13
1Positive +terminal
2Battery wire (sold separately)
The maximum length of the wire between
the fuse and the positive +terminal of the
battery is 30 cm (12 in.).
3Fuse (80 A) (sold separately)
Each amplifier must be separately fused at
80 A.
2 Use wire cutters or a utility knife to
strip the end of the battery wire, ground
wire and system remote control wire to ex-
pose about 10 mm (3/8 in.) of the end of
each of the wires, and then twist the ex-
posed ends of the wires.
Twist
10 mm (3/8 in.)
3 Connect the wires to the terminal.
Fix the wires securely with the terminal
screws.
3
6
1
5
4
2
7
1Battery wire
2Power terminal
3Ground wire
4GND terminal
5System remote control wire
6System remote control terminal
7Terminal screws
<5707000012820V>10
En
Connecting the units
Connecting the speaker output
terminals
1 Use wire cutters or a utility knife to
strip the end of the speaker wires to ex-
pose about 10 mm (3/8 in.) of wire and
then twist the wire.
Twist
10 mm (3/8 in.)
2 Connect the speaker wires to the
speaker output terminals.
Fix the wires securely with the terminal
screws.
1
3
2
1Terminal screws
2Speaker wires
3Speaker output terminals
Before installing the amplifier
WARNING
!To ensure proper installation, use the supplied
parts in the manner specified. If any parts
other than those supplied are used, they may
damage internal parts of the amplifier, or be-
come loose causing the amplifier to shut
down.
!Do not install in:
Places where injury could occur if the boat
stops suddenly.
Places where it may interfere with the
boat's operator.
!Install tapping screws in such a way that the
screw tip does not touch any wire. This is im-
portant to prevent wires from being cut by vi-
bration of the boat, which can result in fire.
!Make sure that wires do not get caught in the
sliding mechanism or touch the legs of a per-
son in the boat as short-circuit may result.
!When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. cables, wiring, hoses, and modules) from
damage.
CAUTION
!To ensure proper heat dissipation of the ampli-
fier, ensure the following during installation:
Allow adequate space above the amplifier
for proper ventilation.
Do not cover the amplifier.
!Place all cables away from hot places, such
as near the heater outlet.
!The optimal installation location differs de-
pending on the boat model. Secure the ampli-
fier at a sufficiently rigid location.
!Check all connections and systems before
final installation.
<5707000012820V>11
En
Connecting the units Installation
Example of installation on
the chassis
1 Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm ×
18 mm (5/32 in. × 3/4 in.)) into the screw holes
and push on the screws with a screwdriver so
they make an imprint where the installation
holes are to be located.
2 Drill 2.5 mm (3/32 in.) diameter holes in
the chassis.
3 Install the amplifier with the use of
supplied tapping screws (4 mm × 18 mm
(5/32 in. × 3/4 in.)).
1
2
34
5
1Tapping-screws (4 mm × 18 mm (5/32 in. ×
3/4 in.))
2Drill a 2.5 mm (3/32 in.) diameter hole
3Installation surface
4Hole-to-hole distance: 229.5 mm (9-1/32 in.)
5Hole-to-hole distance: 191.5 mm
(7-17/32 in.)
4 Attach the fuse cover and panel cover.
Attach the panel cover to the amplifier using
the supplied machine screws (3 mm × 10 mm
(1/8 in. × 3/8 in.)).
Machine screws (3 mm × 10 mm (1/8 in. × 3/
8 in.))
When installing the amplifier in a place that is
prone to getting wet, install it to a wall with
the power/speaker output terminals and RCA
jacks on the left and right sides.
<5707000012820V>12
En
Installation
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer GM-ME500X1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer GM-ME500X1 in the language / languages: English, French as an attachment in your email.

The manual is 1.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer GM-ME500X1

Pioneer GM-ME500X1 User Manual - German, Dutch - 7 pages

Pioneer GM-ME500X1 User Manual - Italian, Spanish - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info