811526
4
Zoom out
Zoom in
Previous page
1/8
Next page
Example of installation on
the chassis
1 Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm ×
18 mm (5/32 in. × 3/4 in.)) into the screw holes
and push on the screws with a screwdriver so
they make an imprint where the installation
holes are to be located.
2 Drill 2.5 mm (3/32 in.) diameter holes in
the chassis.
3 Install the amplifier with the use of
supplied tapping screws (4 mm × 18 mm
(5/32 in. × 3/4 in.)).
1
2
34
5
1Tapping-screws (4 mm × 18 mm (5/32 in. ×
3/4 in.))
2Drill a 2.5 mm (3/32 in.) diameter hole
3Installation surface
4Hole-to-hole distance: 229.5 mm (9-1/32 in.)
5Hole-to-hole distance: 191.5 mm
(7-17/32 in.)
4 Attach the fuse cover and panel cover.
Attach the panel cover to the amplifier using
the supplied machine screws (3 mm × 10 mm
(1/8 in. × 3/8 in.)).
Machine screws (3 mm × 10 mm (1/8 in. × 3/
8 in.))
When installing the amplifier in a place that is
prone to getting wet, install it to a wall with
the power/speaker output terminals and RCA
jacks on the left and right sides.
<5707000013050V>13
En
Installation
Specifications
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system ................... Negative type
Current consumption ............ 26 A (at continuous power,
4W)
Average current consumption
..................................................... 2.6 A (4 Wfor four channels)
3.8 A (4 Wfor two channels,
BRIDGE)
3.8 A (2 Wfor four channels)
Fuse ................................................ 30 A × 2
Dimensions (W × H × D) ... 252 mm × 60 mm ×
215 mm
(9-7/8 in. × 2-3/8 in. ×
8-1/2 in.)
Weight .......................................... 2.4 kg (5.3 lbs)
(Leads for wiring not in-
cluded)
Maximum power output ....... 150 W × 4 (4 W)/400W×2
(4 W) BRIDGE / TOTAL
800 W (400 W × 2)
Continuous power output ... 75 W × 4 (at 14.4 V, 4 W,
20 Hz to 20 kHz, 1 % THD)
100 W × 4 (at 14.4 V, 2 W,
1 kHz, 1 % THD)
150 W × 4 (at 14.4 V, 1 W,
1 kHz, 1 % THD)
200 W × 2 (at 14.4 V, 4 W
BRIDGE, 1 kHz, 1 % THD)
300 W × 2 (at 14.4 V, 2 W
BRIDGE, 1 kHz, 1 % THD)
Load impedance ...................... 4 W(1 Wto 8 Wallowable)
Frequency response ............... 10 Hz to 50 kHz (+0 dB,
3 dB)
Signal-to-noise ratio ............... 95 dB (IEC-A network)
Distortion ..................................... 0.05 % (10 W, 1 kHz)
Low pass filter:
Cut off frequency ........... 40 Hz to 500 Hz
Cut off slope ..................... 12 dB/oct
High pass filter:
Cut off frequency ........... 40 Hz to 500 Hz
Cut off slope ..................... 12 dB/oct
Gain control:
RCA ...................................... 0.2 V to 6.5 V
Speaker .............................. 0.8 V to 16 V
Maximum input level / impedance:
RCA ...................................... 6.5 V / 25 kW
Speaker .............................. 16 V / 12 kW
Accessories
Panel cover × 1
Fuse cover × 1
Speaker input wire × 2
Hexagonal wrench × 1
Mounting screw (4 × 18 mm) × 4
Mounting screw (3 × 10 mm) × 3
Notes
!Specifications and the design are subject to
modifications without notice.
!The average current consumption is nearly
the maximum current consumption by this
unit when an audio signal is input. Use this
value when working out total current con-
sumption by multiple power amplifiers.
<5707000013050V>14
En
Additional information
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer GM-ME400X4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer GM-ME400X4 in the language / languages: English, French as an attachment in your email.

The manual is 2.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer GM-ME400X4

Pioneer GM-ME400X4 User Manual - German, Dutch - 8 pages

Pioneer GM-ME400X4 User Manual - Italian, Spanish - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info