60553
3
Zoom out
Zoom in
Previous page
1/8
Next page
Connecting the Unit
Connecting the Power Terminal
•Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
1. Pass the battery wire from the
engine compartment to the interior
of the vehicle.
After making all other connections to the
amplifier, connect the battery wire terminal of
the amplifier to the positive (+) terminal of
the battery.
2. Twist the battery wire, ground wire
and system remote control wire.
3. Attach lugs to wire ends. Lugs not
supplied.
Use pliers, etc., to crimp lugs to wires.
4. Connect the wires to the terminal.
•Fix the wires securely with the terminal
screws.
Fuse (30 A)
Engine
compart-
ment
Interior of
the vehicle
Drill a 14 mm
(1/2 inch) hole
into the vehicle
body.
Insert the O-ring rubber
grommet into the vehicle
body.
Twist
Positive terminal
GND terminal
Power terminal
Battery wire
System remote
control terminal
System remote
control wire
Ground wire
Connecting the Speaker Output
Terminals
1. Expose the end of the speaker wires
using nippers or a cutter by about
10 mm (3/8 inch) and twist.
2. Attach lugs to speaker wire ends.
Lugs not supplied.
Use pliers, etc., to crimp lugs to wires.
3. Connect the speaker wires to the
speaker output terminals.
•Fix the speaker wires securely with the termi-
nal screws.
10 mm
Twist
Speaker
output
terminal
Terminal screw
Speaker wire
Lug
Fuse (30 A)
Battery wire
Ground wire
Lug
Lug
Speaker wire
Connecting the Speaker wires
The speaker output mode can be two-chan-
nel (stereo), one-channel (mono), or three-
channel (stereo + mono). Connect the
speaker leads to suit the mode according to
the figures shown below.
Two-channel mode (stereo)
One-channel mode (mono)
Three-channel mode (stereo + mono)
The power amplifier is basically a two-
channel/one-channel bridgeable amplifier,
but three channels can be achieved by
combining the stereo and mono modes
using inductors and capacitors.
Three-channel mode, two-way system
Three-channel mode, three-way system
Inductors (L1 and L2 in the diagrams)
act as low-pass filters. Capacitors (C1
and C2 in the diagrams) act as high-pass
filters. Inductors (L) are used for the
woofer/subwoofer, and capacitors (C)
are used for the high/mid-high.
Remember when bridging an amplifier it
will see only half of the original speaker
impedance. Therefore, you must use
speakers that have ratings of 4 ohms or
higher. If you use speakers that have
lower impedance ratings it may cause
damage to the amplifier.
•When the inductors and capacitors are
connected to the speaker wires, secure or
solder them so they cannot be pulled
loose. Tape or use heat shrink on the
joints to prevent short circuits.
C2
C2
L1
L2
L2
C1
C1
C1
C1
L1
(Right)
Speaker
(Left)
Speaker (Mono)
Mid-high (Right)
Woofer (Mono)
Mid-high (Left)
High/mid-high
(Right)
Mid/mid-bass
(Right)
Woofer/subwoofer
(Mono)
Mid/mid-bass
(Left)
High/mid-high
(Left)
Component Guide
Speaker load Impedance 2 4 8
fc (Hz) L (mH) C (µF) L (mH) C (µF) L (mH) C (µF)
50 6.4 1,600 12.70 800.0 25.50 400.0
80 4.0 1,000 8.00 500.0 16.00 250.0
125 2.5 640 5.10 300.0 10.00 160.0
200 1.6 400 3.20 200.0 6.40 100.0
320 1.0 250 2.00 125.0 4.00 62.0
500 0.64 160 1.30 80.0 2.60 40.0
800 0.4 100 0.80 50.0 1.60 25.0
1,250 0.25 64 0.50 30.0 1.00 16.0
2,000 0.16 40 0.30 20.0 0.64 10.0
3,200 0.1 25 0.20 12.5 0.40 6.2
5,000 0.06 16 0.13 8.0 0.26 4.0
8,000 0.04 10 0.08 5.0 0.16 2.5
10,000 0.03 8 0.06 4.0 0.13 2.0
Setting the Filter Constant
Low-pass filter (for subwoofer/woofer):
6 dB/octave
High-pass filter (for mid/mid-high):
6 dB/octave
Band-pass filter (combination of low-pass
filter and high-pass filter for mid-
bass/mid): 6 dB/octave
•A multi-channel system can be set up using a
combination of filters. The inductance (L) and
capacitance (C) will determine the frequency (fc)
that the speaker will reproduce. Refer to the chart
below to determine the components required.
•Use the capacitors specified. Non-polarized capac-
itors rated at over ±25 V should be used for C1
and C2 in the diagram. Because of the voltage
output of the amplifier, it is very important to use
non-polarized capacitors rated at or over 25 V.
This will prevent a safety hazard.
L2
C2
0dB
–6dB
f
CH
2f
CH
f
CL
f
CL
2
0dB
–6dB
f
C
f
f
C
2
C1
0dB
–6dB
f
C
2f
C
f
L1
(3/8 inch)
HRD0259A_Eng 1/21/04 17:12 Page 9
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer GM-5000T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer GM-5000T in the language / languages: English, French as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer GM-5000T

Pioneer GM-5000T User Manual - German, Dutch, Italian, Spanish - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info