649205

Pioneer FH-X840 Manual

19
Zoom out
Zoom in
Previous page
1/204
Next page
19En
English
In the following, "NW" represents network
mode and "STD" represents standard
mode. According to the connections you
have established, change the speaker
mode to standard mode (STD) or network
mode (NW)
(page 5).
Important
• When installing this unit in a vehicle
without an ACC (accessory) position on
the ignition switch, failure to connect the
red cable to the terminal that detects
operation of the ignition key may result
in battery drain.
• Use of this unit in conditions other than
the following could result in fire or
malfunction.
–Vehicles with a 12-volt battery and
neg
a
tive grounding.
–When speaker output is used by 4
channels,
use speakers over 50 W
(maximum input power) and between 4
Ω to 8 Ω (impedance value). Do not use
1 Ω to 3 Ω speakers for this unit.
–When rear speaker output is used by 2
Ω
o
f subwoofer, use speakers over 70 W
(maximum input power).
* Please refer to connections for a
co
nnec
tion method.
• To prevent a short-circuit, overheating or
mal
function, be sure to follow the
directions below.
–Disconnect the negative terminal of the
bat
t
ery before installation.
– Secure the wiring with cable clamps or
adhes
ive tape. Wrap adhesive tape
around wiring that comes into contact
with metal parts to protect the wiring.
– Place all cables away from moving parts,
su
c
h as the shift lever and seat rails.
– Place all cables away from hot places,
such
as near the heater outlet.
– Do not connect the yellow cable to the
batt
ery by passing it through the hole
to the engine compartment.
– Cover any disconnected cable
co
nnec
tors with insulating tape.
– Do not shorten any cables.
– Never cut the insulation of the power
cabl
e o
f this unit in order to share the
power with other devices. The current
capacity of the cable is limited.
– Use a fuse of the rating prescribed.
– Never wire the negative speaker cable
di
r
ectly to ground.
– Never band together negative cables of
mu
ltiple speakers.
• When this unit is on, control signals are
sent
through the blue/white cable.
Connect this cable to the system remote
control of an external power amp or the
vehicle’s auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
vehicle is equipped with a glass antenna,
connect it to the antenna booster power
supply terminal.
• Nev
er connect the blue/white cable to
the power terminal of an external power
amp. Also, never connect it to the power
terminal of the auto antenna. Doing so
may result in battery drain or a
malfunction.
• T
he black cable is ground. Ground cables
f
or this unit and other equipment
(especially, high-current products such as
power amps) must be wired separately. If
Connections/Installation
Connections
ACC position No ACC position
they are not, an accidental detachment
may result in a fire or malfunction.
• The graphical symbol placed on
the product means direct current.
This unit
Microphone (3 m)
Power cord input
Microphone input
Rear output (STD) or middle range
output (NW)
Front output (STD) or high range output
(NW)
DAB antenna input
To receive DAB signals, connect a DAB
ant
e
nna (AN-DAB1) (sold separately) to
the unit.
Antenna input
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can
be connec
t
ed (sold separately).
Subwoofer output
Power cord
To power cord input
Depending on the kind of vehicle, the
function of and may be different.
In this case, be sure to connect to
and to .
Yellow
Back-up (or accessory)
Yellow
Connect to the constant 12 V supply
te
r
minal.
Red
Accessory (or back-up)
Red
Connect to terminal controlled by the
ign
ition switch (12 V DC).
Connect leads of the same colour to
each other.
Black (chassis ground)
Blue/white
The pin position of the ISO connector
w
i
ll differ depending on the type of
vehicle. Connect and when Pin 5
is an antenna control type. In another
t
y
pe of vehicle, never connect and
.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer FH-X840 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer FH-X840 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 19,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info