425037
34
Zoom out
Zoom in
Previous page
1/112
Next page
34
<DRB1317>
En/Fr
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check
the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in
use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.
Problem Possible Cause Countermeasure
The power does not turn
on.
There is little or no sound.
Sound is distorted.
Cant use cross fading.
CD players fader wont
start.
Effects dont work.
External effectors sound
distorted.
Cant measure BPM.
Measured BPM values are
strange.
Measured BPM value
differs from value indicated
on CD.
Cant use CH-4s PHONO 3
input terminal.
÷ The power cord has not been connected.
÷ The input selector switch is in the wrong
position.
÷ The connection cable hasn’t been connected
properly or has been disconnected.
÷ The terminal or plug is dirty.
÷ The master output level control (MASTER
LEVEL ATT.) on the back has been set too
low.
÷ Master output level is too high.
÷ Input level is too high.
÷ ASSIGN A & B haven’t been set correctly.
÷ Fader start switch is off.
÷ The player control terminal on the back hasn’t
been connected.
÷ Effect/sampler selector switch hasn’t been
set correctly.
÷ Effect/sampler parameter 2 knob was set to
the minimum (MIN.).
÷ The input level from the external effector is
too high.
÷ Input level is too high or too low.
÷ BPM can’t be measured in some cases,
depending on the music.
÷ Because of different BPM measurement
methods, somewhat different values may be
indicated.
÷ A sub-microphone has been connected.
÷ Connect the cord to a power outlet.
÷ Set the input selector switch to the device
currently playing.
÷ Connect it properly.
÷ Clean and reconnect.
÷ Adjust the master output level control
(MASTER LEVEL ATT.) on the back.
÷ Adjust the master output level control
(MASTER LEVEL ATT.) on the back.
÷ Adjust the TRIM knob so that the input level
approaches 0dB on the peak level meter.
÷ Set the ASSIGN switches to the correct cross
fader source.
÷ Turn on the fader start switch.
÷ Use the control cable to connect the unit and
CD player.
÷ Correctly select the channel to which effects
should be applied.
÷ Adjust the effect/sampler parameter 2 knob.
÷ Lower the external effector’s output level or
adjust the return level using the effect/
sampler parameter 2 knob.
÷ Adjust the TRIM knob so that the input level
approaches 0dB on the peak level meter.
÷ Adjust input levels of other channels to
approach 0dB.
÷ Press the TAP switch and set BPM manually.
÷ No countermeasures necessary.
÷ Disconnect the sub- microphone.
Static electricity or other external interference may cause the unit to malfunction. To restore normal operation, turn the power off and then
on again.
En
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer djm 600 dj mixer 5 kanaals at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer djm 600 dj mixer 5 kanaals in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info