Manual Pioneer DEH-P3500MP (page 2 of 8) (English, German, Dutch, French, Italian, Spanish)

97757

Zoom out

Zoom in

1/8

Montaje trasero DIN

Instalación usando los agujeros para

tornillos ubicados en ambos costados

de la unidad (Fig. 5) (Fig. 6) (Fig. 7)

1. Quite el marco.

8. Marco

9. Inserte el pasador de liberanción en el orificio de

la parte inferior del marco, y tire hacia afuera

para extaer el marco.

(Para la fijación del marco, apunte el lado con

ranura hacia abajo.)

2. Fijación de la unidad a la ménsula de

montaje existente.

10. Seleccione una posición en la que los orificios

para los tornillos del soporte y del de la unidad

principal queden alineados, y apriete los tornillos

en 2 lugares de un lado. Utilice ya sea los tornil-

los de fijación (5 × 8 mm) o los tornillos a paño

(5 × 9 mm), dependiendo de la forma de los ori-

ficios de tornillo en la ménsula.

11. Tornillo

12. Ménsula de montaje de radio existente

13. Tablero de instrumentos o consola

Colocación del panel delantero

Si no desea utilizar la función de extracción y

colocación del panel delantero, utilice los tornil-

los de fijación suministrados y fije el panel

delantero a esta unidad.

1. Coloque los sujetadores en ambos

lados del panel delantero. (Fig. 8)

14. Sujetador

2. Reinstale el panel delantero en la

unidad. (Fig. 9)

3. Mueva los sujetadores en las posi-

ciones verticales. (Fig. 10)

4. Fije el panel delantero a la unidad

utilizando los tornillos de fijación.

(Fig. 11)

15. Tornillos de fijación

Nota:

• Antes de finalmente instalar la unidad, conecte el

cableado temporalmente y asegúrese de que todo

esté conectado correctamente y que la unidad y

el sistema funcionan debidamente.

• Utilice sólo las piezas que se incluyen con esta

unidad para asegurar la instalación adecuada. El

uso de piezas no autorizadas podría causar fallos

de funcionamiento.

• Consulte con su distribuidor si la instalación

requiere del taladro de orificios u otras modifica-

ciones del vehículo.

• Instale la unidad donde no alcance el espacio del

conductor, y donde no pueda dañar a los

pasajeros si sucediera un paro repentino, como

una detención de emergencia.

• El semiconductor láser se dañará si se sobre-

calienta, por eso no instale la unidad en un lugar

caliente – por ejemplo, cerca de la salida de un

calefactor.

• Si el ángulo de la instalación excede los 60° del

lado horizontal, la unidad podría no brindar su

óptimo funcionamiento. (Fig. 1)

Montaje delantero/trasero DIN

Esta unidad quede instalarse correstamente de la

“Delantera” (montaje delantero DIN conven-

ciona) o “Trasera” (montaje trasero DIN, uti-

lizando los tornillos roscados en los constados

del chasis de la unidad). Para detalles, refiérase a

los métodos de instalación ilustrados abajo.

Montaje delantero DIN

Instalación con tope de goma (Fig. 2)

1. Tablero de instrumentos

2. Soporte

Después de insertar el soporte en la tabla de

mandos, luego seleccione las orejetas apropiadas

según el grosor del material de la tabla de man-

dos y dóblelos.

(Instale lo más firme posible usando las lengüe-

tas superior e inferior. Para fijar, doble las

lengüetas 90 grados.)

3. Tope de goma

4. Tornillo

Quitado de la unidad (Fig. 3) (Fig. 4)

5. Marco

6. Inserte el pasador de liberanción en el orificio de

la parte inferior del marco, y tire hacia afuera

para extraer el marco.

(Para la fijación del marco, apunte el lado con

ranura hacia abajo.)

7. Inserte las herramientas de extracción sumin-

istradas en la unidad, como se indica en la figura,

hasta que se enganchen en su posición.

Tire de la unidad mientras mantiene las her-

ramientas presionadas contra los lados de la

unidad.

DIN Rear-mount

Installation using the screw holes on

the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)

1. Remove the frame.

8. Frame

9. Insert the release pin into the hole in the bottom

of the frame and pull out to remove the frame.

(When reattaching the frame, point the side with

a groove downwards and attach it.)

2. Fastening the unit to the factory

radio mounting bracket.

10. Select a position where the screw holes of the

bracket and the screw holes of the head unit

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either truss

screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw

holes in the bracket.

11. Screw

12. Factory radio mounting bracket

13. Dashboard or Console

Fixing the Front Panel

If you do not operate the Detaching and

Replacing the Front Panel Function, use the sup-

plied fixing screws and fix the front panel to this

unit.

1. Attach the holders to both sides of

the front panel. (Fig. 8)

14. Holder

2. Replace the front panel to the unit.

(Fig. 9)

3. Flip the holders into upright posi-

tions. (Fig. 10)

4. Fix the front panel to the unit using

fixing screws. (Fig. 11)

15. Fixing screw

Note:

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connect-

ed up properly, and the unit and the system work

properly.

• Use only the parts included with the unit to

ensure proper installation. The use of unautho-

rized parts can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

• Install the unit where it does not get in the dri-

ver’s way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.

(Fig. 1)

DIN Front/Rear-mount

This unit can be properly installed either from

“Front” (conventional DIN Front-mount) or

“Rear” (DIN Rear-mount installation, utilizing

threaded screw holes at the sides of unit chassis).

For details, refer to the following illustrated

installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 2)

1. Dashboard

2. Holder

After inserting the holder into the dashboard,

then select the appropriate tabs according to the

thickness of the dashboard material and bend

them.

(Install as firmly as possible using the top and

bottom tabs. To secure, bend the tabs 90

degrees.)

3. Rubber bush

4. Screw

Removing the Unit (Fig. 3) (Fig. 4)

5. Frame

6. Insert the release pin into the hole in the bottom

of the frame and pull out to remove the frame.

(When reattaching the frame, point the side with

a groove downwards and attach it.)

7. Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into place.

Keeping the keys pressed against the sides of the

unit, pull the unit out.

Instalación <ESPAÑOL>Installation <ENGLISH>

CRD3675A 02.10.21 11:18 AM Page 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer DEH-P3500MP in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer DEH-P3500MP

Pioneer DEH-P3500MP User Manual - German - 100 pages

Pioneer DEH-P3500MP User Manual - Dutch - 96 pages

Pioneer DEH-P3500MP User Manual - Danish - 92 pages

Pioneer DEH-P3500MP User Manual - French - 100 pages

Pioneer DEH-P3500MP User Manual - Italian - 96 pages

Pioneer DEH-P3500MP User Manual - Swedish, Norwegian - 92 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer DEH-P3500MP Manual

Product: