Manual Pioneer DEH-6300SD (page 9 of 136) (English, German, Dutch, French, Italian, Spanish)

454467

Zoom out

Zoom in

1/136

Audio Adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select AUDIO.

3 Turn M.C. to select the audio function.

After selecting, perform the following proce-

dures to set the audio function.

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between fader (front/rear)

and balance (left/right).

3 Turn M.C. to adjust the speaker balance.

! When the rear output setting is SW, you

cannot adjust front/rear speaker balance.

Refer to SW CONTROL (rear output and

subwoofer setting) on the next page.

PRESET EQ (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select an equalizer curve.

POWERFUL—NATURAL—VOCAL—CUS-

TOM1—CUSTOM2—FLAT—SUPER BASS

3 Press M.C. to confirm the selection.

GRAPHIC EQ (equalizer adjustment)

You can adjust the currently selected equalizer

curve setting as desired. Adjusted equalizer curve

settings are stored in CUSTOM1 or CUSTOM2.

! A separate CUSTOM1 curve can be created

for each source. If you make adjustments

when a curve other than CUSTOM2 is se-

lected, the equalizer curve settings will be

stored in CUSTOM1.

! A CUSTOM2 curve that is common for all

sources can be created. If you make adjust-

ments when the CUSTOM2 curve is selected,

the CUSTOM2 curve will be updated.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between equalizer band

and level.

3 Press M.C. to switch to equalizer band and

then turn M.C. to select.

100HZ—315HZ—1.25KHZ—3.15KHZ—8KHZ

4 Press M.C. to switch to level and then turn M.

C. to adjust.

Adjustment range: +6 to –6

LEVEL METER (level meter display setting)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

OFF (off)—MODE1—MODE2—MODE3—

MODE4

3 Press M.C. to confirm the selection.

LOUDNESS (loudness)

Loudness compensates for deficiencies in the low-

and high-frequency ranges at low volume.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HIGH

(high)

3 Press M.C. to confirm the selection.

SW SETTING 1 (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

NORMAL (normal phase)—REVERSE (reverse

phase)—OFF (subwoofer off)

3 Press M.C. to confirm the selection.

SW SETTING 2 (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off fre-

quency and output level of the subwoofer.

3 Press M.C. to switch to cut-off frequency and

then turn M.C. to select the cut-off frequency.

50HZ—63HZ—80HZ—100HZ—125HZ

4 Press M.C. to switch to output level and then

turn M.C. to adjust the output level.

Adjustment range: +6 to -24

HPF SETTING (high pass filter adjustment)

When you do not want low sounds from the sub-

woofer output frequency range to play from the

front or rear speakers, turn on the HPF (high pass

filter). Only frequencies higher than those in the

selected range are output from the front or rear

speakers.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the cut-off frequency.

OFF (off)—50HZ—63HZ—80HZ—100HZ—

125HZ

3 Press M.C. to confirm the selection.

BASS BOOSTER (bass boost)

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the level.

Adjustment range: 0 to +6

3 Press M.C. to confirm the selection.

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

! When selecting FM as the source, you cannot

switch to SLA.

! Settings are based on the FM volume level,

which remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Initial Settings

1 Press and hold SRC/OFF until the unit

turns off.

2 Press M.C. and hold until the initial set-

ting menu appears in the display.

3 Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock

display you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

CLOCK (clock on/off setting)

1 Press M.C. to turn the clock display on or off.

FM STEP (FM tuning step)

English

Operating this unit

Section

Operating this unit

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer DEH-6300SD in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer DEH-6300SD Manual

Product: