625522
178
Zoom out
Zoom in
Previous page
1/232
Next page
Before operating the Auto EQ function
! Perform Auto EQ in as quiet a place as pos-
sible, with the vehicle engine and air condi-
tioning switched off. Also, cut power to car
phones or cellular phones in the vehicle, or
remove them from the vehicle before per-
forming Auto EQ. Sounds other than the
measurement tone (surrounding sounds,
engine sound, telephones ringing, etc.)
may prevent correct measurement of the
vehicles acoustics.
! Be sure to perform Auto EQ using the mi-
crophone for acoustical measurement
(sold separately). Using another micro-
phone may prevent measurement, or result
in incorrect measurement of the vehicles
acoustics.
! To perform Auto EQ, the front speakers
must be connected.
! When this navigation system is connected
to a power amp with input level control,
Auto EQ may not be able to be performed if
the power amps input level is set below
the standard level.
! When this navigation system is connected
to a power amp with an LPF, turn the LPF
off before performing Auto EQ. Also, set
the cut-off frequency for the built-in LPF of
an active subwoofer to the highest fre-
quency.
! The distance has been calculated by com-
puter to provide the optimum delay to en-
sure accurate results. Do not change this
value.
The reflected sound within the vehicle is
strong and delays occur.
The LPF on active subwoofers or exter-
nal amps delay the lower sounds.
! If an error occurs during measurement, a
message appears and measurement is
canceled. Check the following before mea-
suring the vehicles acoustics.
Front speakers (left/right)
Rear speakers (left/right)
Noise
Microphone for acoustical measure-
ment (sold separately)
Low battery
Performing Auto EQ
p Auto EQ changes the audio settings as fol-
lows:
! Auto EQ on the EQ Menu screen is
set to On.
= For details, refer to Using the auto-ad-
justed equalizer on the previous
page.
! The fader/balance settings return to the
center position.
= For details, refer to Using balance ad-
justment on page 175.
! The equalizer curve switches to Flat.
= For details, refer to Using the equali-
zer on page 175.
! The front and rear speakers will automa-
tically be adjusted to a high pass filter
setting.
p Previous settings for Auto EQ will be over-
written.
p For AVIC-Z130BT users
Do not press the h button to open or close
the panel when you are using the micro-
phone.
1 Stop the vehicle in a place that is quiet,
close all the doors, windows and sun roof,
and then turn the engine off.
If the engine is left running, engine noise may
prevent correct Auto EQ.
p If driving restrictions are detected during
measurement, measurement is canceled.
2 Fix the microphone for acoustical mea-
surement (sold separately) in the center of
the headrest of the drivers seat, facing for-
ward.
The Auto EQ may differ depending on where
you place the microphone. If desired, place
the microphone on the front passenger seat
and perform Auto EQ.
En
178
Chapter
32
Customizing preferences
178


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-X930BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-X930BT in the language / languages: English as an attachment in your email.

The manual is 13,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info