62771
139
Zoom out
Zoom in
Previous page
1/164
Next page
137
AppendixNAVI/AV
Problems in the audio screen (during iPod playback)
Messages and how to react to them
The following messages may be displayed by your navigation system.
There are occasions when you may see error messages other than those shown here. In such a
case, follow the instructions given on the display.
Symptom Cause Action (See)
Cannot be operated. The iPod is frozen. Reconnect the iPod with the inter-
face cable for iPod
®
(sold sepa-
rately).
The authorisation error has occurred. Reconnect the iPod with the inter-
face cable for iPod
®
(sold sepa-
rately).
Set the ACC to Off and set it to On
again.
Update the iPod version.
Message When What to do
Please insert the appropriate disc.
This is not the appropriate disc.
Please insert the appropriate disc.
If you try to use a disc which is
incompatible with this system.
Insert a suitable disc.
If you insert a disc upside down. Insert the disc with the label upward.
If the disc is dirty. Clean the disc.
If the disc is cracked or otherwise
damaged.
Insert a normal, round disc.
Irregular speed pulse signal is
detected. Please turn system power
off and check the installation. After
checking, please re-boot the system
and press “OK”.
If the Navigation system does not
receive the vehicle speed pulse.
Consult your Pioneer dealer.
Speed pulse wire is not connected.
Please be sure to connect the system
to the speed pulse wire. Accuracy is
not fully ensured without speed
pulse.
The speed signal input (pink lead
wire) of the power cable is not con-
nected.
To operate with 3D hybrid mode, con-
nect the speed signal input (pink
lead wire) of the power cable cor-
rectly.
Although it can be operated with
Simple hybrid mode without con-
necting the speed signal input, the
precision of the positioning will be
less accurate.
Vibration is detected. Please turn
system power off and check the
installation. After checking, please
re-boot the system and press “OK”.
The navigation unit is installed in a
place where it may be affected by a
large vibration.
Re-install the navigation unit in a
place where the unit will not be
affected by vibration.
Direction of G sensor is not correct.
Please turn system power off and
check the installation. After check-
ing, please re-boot the system and
press “OK”.
Direction of G sensor is set incor-
rectly.
See the “Installation Manual” and set
the direction of the navigation unit
correctly.
Gyro Sensor is not working properly.
Please consult your dealer or Pioneer
service centre.
Abnormal output is detected from
the Gyrosensor.
Note down the error code shown on
the screen. Turn off the power, and
then contact your nearest Pioneer
service facility.
This function is not available now. The screen cannot be displayed with
Vehicle Dynamics Display.
Because the sensor has not been
taught so the sensor information
cannot be acquired.
If the sensor learning status reaches
the Sensor Initialising status, the sys-
tem is ready to be used.
MAN-AVIC-X3-EN.book Page 137 Wednesday, June 6, 2007 10:15 AM
139


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-X3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-X3 in the language / languages: English as an attachment in your email.

The manual is 8,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVIC-X3

Pioneer AVIC-X3 Installation Guide - English, German - 182 pages

Pioneer AVIC-X3 User Manual - German - 188 pages

Pioneer AVIC-X3 Installation Guide - Dutch - 182 pages

Pioneer AVIC-X3 User Manual - Dutch - 184 pages

Pioneer AVIC-X3 Installation Guide - French - 182 pages

Pioneer AVIC-X3 User Manual - French - 176 pages

Pioneer AVIC-X3 Installation Guide - Italian, Spanish - 182 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info