62771
136
Zoom out
Zoom in
Previous page
1/164
Next page
134
Appendix NAVI/AV
Your vehicle is operating in Simple
hybrid mode.
Connect the speed signal input (pink
lead wire) of the power cable cor-
rectly, and reset the 3D Hybrid Sen-
sor memory (“Learning Status”).
The navigation system is installed
with an extreme angle exceeding the
limitation of the installation angle.
Confirm the installation angle. (The
navigation system must be installed
within the allowed installation angle.
For details, refer to “Installation Man-
ual”.)
Indication of the position of your vehi-
cle is misaligned after a U-turn or
reversing.
Check whether or not the reverse
gear signal input lead (purple) is con-
nected properly. (The navigation sys-
tem works properly without the lead
connected, but positioning accuracy
will be adversely affected.)
The map continually reorients itself. The travelling direction is set to
Heading Up.
Touch on the screen and change
the map display.
Tracking marks are not displayed. The “Tracking Display” is turned
off.
Check the “Tracking Display” set-
tings ( Page 65) and make sure
Always” or “This Trip” is selected.
The daylight display is used even
when the vehicle lights are on.
Daytime” is set to “Day/Night Dis-
play”.
Check the “Day/Night Display” set-
ting ( Page 65) and make sure
Illuminated” is selected.
The orange/white lead is not con-
nected.
Check the connection.
The system will not switch on or will
not operate.
Installation or connection has been
carried out incorrectly.
Check with your dealer.
The display is very dim. The vehicle’s light is turned ON, and
Illuminated” is selected on “Day/
Night Display”.
Read about the “Day/Night Dis-
play” setting ( Page 65) and, if
desired, select “Daytime”.
The vehicle cabin temperature is
extremely low.
A Liquid Crystal Display (LCD) is
used, and such displays tend to
darken when cold. Wait for the vehi-
cle to warm up.
Picture quality adjustment of the dis-
play is not correct.
Refer to “Operating the Picture
Adjustment” to adjust the picture
quality.
No sounds are heard.
The volume level will not rise.
The volume level is low. Adjust the volume level.
The attenuator or mute is on. Turn the attenuator or mute off.
The speaker lead is disconnected. Check the connection.
Adjusting the volume of navigation
guidance and beeps is not possible.
You cannot adjust them with the
VOLUME knob.
Turn the volume up or down accord-
ing to “Volume” ( Page 63) in the
Settings” menu.
A strange sound is heard when the
vehicle comes close to a certain
place. (E.g. Dog barking)
The sound for the entry of “Address
Book” is set.
Set the sound setting of that entry to
No Sound”. ( Page 52)
Slope is not displayed on the
Vehicle Dynamics screen.
Inclination does not move on the 3D
Calibration Status screen.
The speed pulse lead is not con-
nected.
Connect the speed pulse lead.
The person on the other end of the
phone call cannot hear the conversa-
tion due to an echo.
The voice from the person on the
other end of the phone call is output
from the speakers and then picked
up by the microphone again, creat-
ing an echo.
Use the following methods to reduce
the echo.
Lower the volume on the receiver
Have both speakers pause
slightly before speaking
Symptom Cause Action (See)
MAN-AVIC-X3-EN.book Page 134 Wednesday, June 6, 2007 10:15 AM
136


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-X3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-X3 in the language / languages: English as an attachment in your email.

The manual is 8,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVIC-X3

Pioneer AVIC-X3 Installation Guide - English, German - 182 pages

Pioneer AVIC-X3 User Manual - German - 188 pages

Pioneer AVIC-X3 Installation Guide - Dutch - 182 pages

Pioneer AVIC-X3 User Manual - Dutch - 184 pages

Pioneer AVIC-X3 Installation Guide - French - 182 pages

Pioneer AVIC-X3 User Manual - French - 176 pages

Pioneer AVIC-X3 Installation Guide - Italian, Spanish - 182 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info