162189
138
Zoom out
Zoom in
Previous page
1/155
Next page
136
Appendix NAVI/AV
Speed pulse wire is not connected.
Please be sure to connect the system
to the speed pulse wire. Accuracy is
not fully ensured without speed
pulse.
The speed signal input (pink lead
wire) of the power cable is not con-
nected.
To operate with 3D hybrid mode, con-
nect the speed signal input (pink
lead wire) of the power cable cor-
rectly.
Although it can be operated with
Simple hybrid mode without con-
necting the speed signal input, the
precision of the positioning will be
less accurate.
Vibration is detected. Please turn
system power off and check the
installation. After checking, please
re-boot the system and press “OK”.
The navigation system is installed in
a place where it may be affected by a
large vibration.
Re-install the Hide-away unit in a
place where the unit will not be
affected by vibration.
Direction of G sensor is not correct.
Please turn system power off and
check the installation. After check-
ing, please re-boot the system and
press “OK”.
Direction of G sensor is set incor-
rectly.
See the “Installation Manual” and set
the direction of the Hide-away unit
correctly.
Gyro Sensor is not working properly.
Please consult your dealer or Pioneer
service centre.
Abnormal output of Gyrosensor is
detected.
Note down the error code shown on
the screen; turn off the power, and
then contact your nearest Pioneer
service facility.
This function is not available now. The screen cannot be displayed with
Vehicle Dynamics Display.
Because the sensor has not been
taught so the sensor information
cannot be acquired.
If the sensor learning status reaches
the Sensor Initialising status or
more, the system is ready to be used.
System detected that the vertical
angle of the installation has been
changed. Learning status for Gyro
Sensor has been initialised.
If the mounting angle of the Hide-
away unit has been changed.
The system initialises the sensor in
order to operate it with the maximum
performance and automatically
starts re-learning.
System detected that the vertical
angle of the installation exceeds the
permission level. Please install the
navigation unit correctly.
The navigation system is installed
with an extreme angle exceeding the
limitation of the installation angle.
Confirm the installation angle. (The
navigation system must be installed
within +30 degrees to
30 degrees
of the horizontal, or within five
degrees of your vehicle’s direction of
travel.)
Route calculation was not possible. Route calculation has failed because
of malfunction of map data, software,
hardware, or disc.
• Change the destination.
• Clean the disc.
• Consult the Pioneer Local dealer if
this message persists.
Route calculation was not possible
because the destination is too far.
The destination is too far. • Set a destination closer to the start-
ing point.
• Set one or more way points.
Route calculation was not possible
because the destination is too near.
The destination or way point(s) are
too close.
Set a destination [and way point(s)]
farther from the starting point.
Route calculation was not possible
due to traffic regulations.
• The destination or way point(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
• Your vehicle is currently in a Con-
trol Traffic Zone (CTR) and the
route calculation is hampered.
• Set a destination and way point(s)
outside the CTR if you know where
the restricted area is.
• Try the destination or way point(s)
away from the currently set points
to some extent.
• Drive your vehicle to an unre-
stricted area and reset the destina-
tion and way point(s).
Route calculation was not possible
because no guidance can be pro-
vided around the destination or the
starting point.
The destination, way point(s), or
starting point are in an area where no
road exists (e.g. a mountain) and the
route calculation is impossible.
• Set a destination and way point(s)
on roads.
• Reset the destination after you
drive the vehicle to any road.
Message When What to do
138


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer avic-x1bt at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer avic-x1bt in the language / languages: English as an attachment in your email.

The manual is 8,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer avic-x1bt

Pioneer avic-x1bt User Manual - English - 26 pages

Pioneer avic-x1bt Installation Guide - English - 194 pages

Pioneer avic-x1bt User Manual - German - 32 pages

Pioneer avic-x1bt User Manual - German - 176 pages

Pioneer avic-x1bt Installation Guide - German - 194 pages

Pioneer avic-x1bt User Manual - Dutch - 176 pages

Pioneer avic-x1bt Installation Guide - Dutch - 194 pages

Pioneer avic-x1bt Quick start guide - Dutch - 2 pages

Pioneer avic-x1bt User Manual - French - 32 pages

Pioneer avic-x1bt User Manual - French - 172 pages

Pioneer avic-x1bt Installation Guide - French, Italian, Spanish - 194 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info