162189
128
Zoom out
Zoom in
Previous page
1/155
Next page
126
Appendix NAVI/AV
The accuracy of the GPS information depends on
how good the reception is. When the signals are
strong and reception is good, GPS can determine
latitude, longitude, and altitude for accurate posi-
tioning in three dimensions. But if signal quality
is poor, only two dimensions, latitude and longi-
tude, can be obtained and positioning errors are
somewhat greater.
Positioning by dead reckoning
The 3D Hybrid Sensor in the navigation system
also calculates your position. The current loca-
tion is measured by detecting driving distance
with the speed pulse, the turning direction with
the Gyrosensor, and inclination of the road with
the G sensor.
The 3D Hybrid Sensor can even calculate
changes of altitude, and corrects for discrepan-
cies in the distance travelled caused by driving
along winding roads or up slopes. Also, the navi-
gation system learns the driving conditions and
stores information in the memory; thus, as you
drive more, the precision of the positioning
becomes more accurate.
The method of positioning changes as follows
depending on whether the speed pulse of your
vehicle is detected or not:
3D hybrid mode
This is active when the speed pulse is detected.
Inclination of a road can be detected.
Simple hybrid mode
When the speed pulse is not detected, position-
ing is performed in this mode. Only horizontal
movement is detected, so it becomes less accu-
rate. Also, when the positioning by GPS is not
available, such as when your vehicle enters a
long tunnel, the discrepancy between your actual
and calculated position may become bigger.
The speed pulse data comes from the speed
sensing circuit. The location of this speed
sensing circuit depends on your vehicle
model. In some cases, it is impossible to
make a connection to it, and in such a case
we recommend that the ND-PG1 speed pulse
generator (sold separately) be used.
How do GPS and dead reckon-
ing work together?
For maximum accuracy, your navigation system
continually compares GPS data with your esti-
mated position as calculated from the data of 3D
Hybrid Sensor. However, if only the data from the
3D Hybrid Sensor is available for a long period,
positioning errors are gradually compounded
until the estimated position becomes unreliable.
For this reason, whenever GPS signals are availa-
ble, they are matched with the data of the 3D
Hybrid Sensor and used to correct it for improved
accuracy.
To ensure maximum accuracy, the dead reckon-
ing system learns with experience. By comparing
the position it estimates with your actual position
as obtained using GPS, it can correct for various
types of error, such as tyre wear and the rolling
motion of your vehicle. As you drive, the dead
reckoning system gradually gathers more data,
learns more, and the accuracy of its estimates
gradually increases. So, after you have driven
some distance, you can expect your position as
shown on the map to show fewer errors.
If you use chains on your wheels for winter
driving or put on the spare wheel, errors may
suddenly increase because of difference in
wheel diameter. The system detects the fact
that the tyre diameter has changed, and auto-
matically replaces the value for calculating
distance.
If the ND-PG1 is used or if your vehicle is oper-
ating in Simple hybrid mode, the distance cal-
culation value cannot be replaced
automatically.
128


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer avic-x1bt at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer avic-x1bt in the language / languages: English as an attachment in your email.

The manual is 8,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer avic-x1bt

Pioneer avic-x1bt User Manual - English - 26 pages

Pioneer avic-x1bt Installation Guide - English - 194 pages

Pioneer avic-x1bt User Manual - German - 32 pages

Pioneer avic-x1bt User Manual - German - 176 pages

Pioneer avic-x1bt Installation Guide - German - 194 pages

Pioneer avic-x1bt User Manual - Dutch - 176 pages

Pioneer avic-x1bt Installation Guide - Dutch - 194 pages

Pioneer avic-x1bt Quick start guide - Dutch - 2 pages

Pioneer avic-x1bt User Manual - French - 32 pages

Pioneer avic-x1bt User Manual - French - 172 pages

Pioneer avic-x1bt Installation Guide - French, Italian, Spanish - 194 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info