6663
171
Zoom out
Zoom in
Previous page
1/192
Next page
169
AppendixNAVI/AV
Signals from the vehicle’s speed
pulse are not being picked up prop-
erly.
Check that the cables are properly
connected. If necessary, consult the
dealer that installed the system.
The navigation system may not be
mounted securely in your vehicle.
Check that the navigation system is
securely mounted and, if necessary,
consult the dealer that installed the
system.
Your vehicle is operating in Simple
hybrid mode.
Connect the speed signal input (pink
lead wire) of the power cable cor-
rectly, and reset the 3D Hybrid Sen-
sor memory ([Learning Status]).
The navigation system is installed
with an extreme angle exceeding the
limitation of the installation angle.
Confirm the installation angle. (The
navigation system must be installed
within the allowed installation angle.
For details, refer to “Installation Man-
ual” and [Installation Angle Setup]
on page 81.)
Indication of the position of your vehi-
cle is misaligned after a U-turn or
reversing.
Check whether or not the reverse
gear signal input lead (purple) is con-
nected properly. (The navigation sys-
tem works properly without the lead
connected, but positioning accuracy
will be adversely affected.)
The map continually reorients itself. The travelling direction is always set
to Heading Up.
Touch on the screen and change
the map display.
The daylight display is used even
when the vehicle lights are on.
[Day] is selected to [Day/Night Dis-
play].
Check the [Day/Night Display] set-
ting ( Page 43) and make sure
[Automatic] is selected.
The orange/white lead is not con-
nected.
Check the connection.
The display is very dim. The vehicle’s light is turned ON, and
[Automatic] is selected on [Day/
Night Display].
Read about the [Day/Night Dis-
play] setting ( Page 43) and, if
desired, select [Day].
The vehicle cabin temperature is
extremely low.
A Liquid Crystal Display (LCD) is
used, and such displays tend to
darken when cold. Wait for the vehi-
cle to warm up.
Picture quality adjustment of the dis-
play is not correct.
Refer to “Operating the picture
adjustment” ( Page 140) to adjust
the picture quality.
Display tilt is not proper setting. Press and hold EJECT button to
adjust the tilt.
No sounds are heard.
The volume level will not rise.
The volume level is low. Adjust the volume level.
The attenuator or mute is on. Turn the attenuator or mute off.
The speaker lead is disconnected. Check the connection.
Volume of beeps and navigation
guidance cannot be adjusted.
You cannot adjust these parameters
with the VOL (8/2) button.
Turn the volume up or down with
[Volume] in the [Settings] menu.
Adjusting the volume of navigation
guidance and beep is not possible.
You cannot adjust them with the
VOL (8/2) button.
Turn the volume up or down accord-
ing to [Volume] ( Page 77) in the
Settings menu.
A strange sound is heard when the
vehicle comes close to a certain
place. (E.g. Dog barking)
The sound for the registered location
is set.
Set the sound of that registered loca-
tion to [No Sound]. ( Page 58)
Slope is not displayed on the
Vehicle Dynamics screen.
Inclination does not move on the 3D
Calibration screen.
The speed pulse lead is not con-
nected.
Connect the speed pulse lead.
Symptom Cause Action (See)
MAN-HD1BT-SOFTW-EN.book Page 169 Thursday, April 20, 2006 3:47 PM
171


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-HD1BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-HD1BT in the language / languages: English as an attachment in your email.

The manual is 10,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVIC-HD1BT

Pioneer AVIC-HD1BT Installation Guide - English - 170 pages

Pioneer AVIC-HD1BT User Manual - German - 208 pages

Pioneer AVIC-HD1BT User Manual - German - 30 pages

Pioneer AVIC-HD1BT Installation Guide - German - 170 pages

Pioneer AVIC-HD1BT User Manual - Dutch - 204 pages

Pioneer AVIC-HD1BT User Manual - Dutch - 30 pages

Pioneer AVIC-HD1BT Installation Guide - Dutch - 170 pages

Pioneer AVIC-HD1BT User Manual - Dutch - 203 pages

Pioneer AVIC-HD1BT User Manual - French - 204 pages

Pioneer AVIC-HD1BT User Manual - French - 30 pages

Pioneer AVIC-HD1BT Installation Guide - French, Italian, Spanish - 170 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info