649251
65
Zoom out
Zoom in
Previous page
1/87
Next page
65
power to car phones or mobile phones in the vehicle, or
remove them in advance. Surrounding sounds may prevent
correct measurement of the vehicle’s acoustics.
Be sure to use the microphone for acoustical measurement
(sold separately). Using another microphone may prevent
measurement, or result in incorrect measurement of the
vehicle’s acoustics.
To perform Auto EQ, the front speakers must be connected.
When this product is connected to a power amp with input
level control, Auto EQ may be impossible if the power amp’s
input level is set below the standard level.
When this product is connected to a power amp with an LPF
(low pass filter), turn the LPF off before performing Auto EQ.
Also, set the cut-off frequency for the built-in LPF of an active
subwoofer to the highest frequency.
The distance has been calculated by a computer to provide
optimum delay to ensure accurate results. Do not change
this value.
The reflected sound within the vehicle is strong and delays
occur.
The LPF on active subwoofers or external amps delay the
lower sounds.
If an error occurs during measurement, check the following
before measuring the vehicle’s acoustics.
Front speakers (left/right)
Rear speakers (left/right)
— Noise
Microphone for acoustical measurement (sold separately)
Low battery
Performing Auto EQ
CAUTION
Do not turn off the engine while the measurement is in
progress.
p
Auto EQ changes the audio settings as follows:
The fader/balance settings return to the centre position.
Refer to Using fader/balance adjustment on page 63
— “Mute Level” is set to “Off”.
Refer to Switching sound muting/attenuation on page 63
p
Previous settings for Auto EQ will be overwritten.
1 Stop the vehicle in a quiet place, close all the
doors, windows and sun roof, and then turn the
engine off.
If the engine is left running, engine noise may prevent correct
Auto EQ.
p
If driving restrictions are detected during measurement,
measurement is cancelled.
2 Fix the microphone for acoustical measurement
(sold separately) in the centre of the headrest
of the driver’s seat, facing forwards.
The Auto EQ may differ depending on where you place the micro-
phone. If desired, place the microphone on the front passenger
seat and perform Auto EQ.
3 Disconnect the iPhone or smartphone device.
4 Turn on the ignition switch (ACC ON).
If the vehicle’s air conditioner or heater is turned on, turn it off.
5 Turn the source off.
Refer to Selecting a source on page 9
6 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 63
7 Touch [A-EQ&TA Measurement].
8 Connect the microphone for acoustical meas-
urement (sold separately) with this product.
F88DAB
F80DAB
Plug the microphone into the auto EQ microphone input jack on
this product.
Refer to Checking part names and functions on page 4
F980DAB
F980BT
Plug the microphone into the AUX input jack on the back panel
of this product.
Refer to the Installation Manual.
p Use an extension cable (sold separately) if the cord of the
Microphone (sold separately) is not long enough.
9 Touch [Front Left] or [Front Right] to select the
current listening position.
10 Touch [Start].
A 10-second countdown starts.
p
The Bluetooth connection is disconnected before the pro-
cess starts.
11 Exit the vehicle and keep the doors closed until
the countdown finishes.
When the countdown finishes, a measurement tone (noise)
is emitted from the speakers and the Auto EQ measurement
begins.
12 Wait until the measurement is completed.
When Auto EQ is completed, a message is displayed.
p
The measurement time varies depending on the type of
vehicle.
To stop the measurement, touch [Stop].
13 Store the microphone carefully in the glove box
or another safe place.
If the microphone is subjected to direct sunlight for an extended
period, high temperatures may cause distortion, colour change
or malfunction.
Using the automatic sound levelizer
During driving, noise in the car changes according to the driving
speed and road conditions. ASL (automatic sound levelizer)
monitors such varying noise and automatically increases the
volume level, if this noise becomes greater. The sensitivity
(variation of volume level to noise level) of ASL can be set to one
of five levels.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 63
2 Touch [ASL].
3 Touch the desired level.
< CRB4818-B >
Audio adjustments
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-F980DAB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-F980DAB in the language / languages: English as an attachment in your email.

The manual is 16,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVIC-F980DAB

Pioneer AVIC-F980DAB Installation Guide - English, German - 204 pages

Pioneer AVIC-F980DAB User Manual - German - 95 pages

Pioneer AVIC-F980DAB Installation Guide - Dutch - 204 pages

Pioneer AVIC-F980DAB User Manual - Dutch - 91 pages

Pioneer AVIC-F980DAB Installation Guide - French - 204 pages

Pioneer AVIC-F980DAB User Manual - French - 93 pages

Pioneer AVIC-F980DAB Installation Guide - Italian, Spanish - 204 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info