649255
57
Zoom out
Zoom in
Previous page
1/78
Next page
57
Adjusting the speaker output
levels nely
Fine adjustments of the speaker output level can be made by
listening to audio output.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 56
2 Touch [Speaker Level].
3 Touch [<] or [>] to select the listening position
if necessary.
The following items are available:
Off, Front-L, Front-R, Front, All.
p
The default setting is “Off”.
p
If you change the setting for the listening position, the
output levels of all the speakers will change according to the
setting.
4 Touch [<] or [>] to adjust the speaker output
level.
p–24” dB to “10” dB is displayed as the level to be corrected
is increased or decreased.
The following items are available:
Front Left, Front Right, Rear Left, Rear Right, Subwoofer
p
If the Auto EQ measurement has been done, the result of the
Auto EQ measurement will be applied by touching [Apply
Auto EQ] (the results are also applied to some settings
simultaneously).
Adjusting the time alignment
By adjusting the distance from each speaker to the listening
position, time alignment is able to correct the time required for
sound to reach the listening position.
1 Measure the distance between the head of the
listener and each speaker unit.
2 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 56
3 Touch [Time Alignment].
4 Touch [<] or [>] to select the listening position
if necessary.
The following items are available:
Off, Front-L, Front-R, Front, All.
p
The default setting is “Off”.
p
If you change the listening position setting, the distance
value of all the speakers will change in conjunction with the
setting.
5 Touch [<] or [>] to input the distance between
the selected speaker and the listening position.
The following items are available:
Front Left, Front Right, Rear Left, Rear Right, Subwoofer
p
You can input the value between 0 cm and 500 cm.
p The distance can be adjusted manually only when the listen-
ing position setting is set to “Front-L” or “Front-R”.
p
If the Auto EQ measurement has been done, the result of the
Auto EQ measurement will be applied by touching [Apply
Auto EQ] (the results are also applied to some settings
simultaneously).
If you touch [TA On], the time alignment is turned
off mandatorily.
Using the equaliser
Recalling equaliser curves
There are multiple equalizer curves that you can easily recall at
any time. The equalizer curves you can recall are as follows:
S.Bass, Powerful, Natural, Vocal, Flat, Custom1 and Custom2
p
The default setting is “Powerful”.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 56
2 Touch [Graphic EQ].
3 Touch the equalizer curve name.
Customising the equaliser curves
p If the preset equalizer curve other than “Custom1” or
Custom2” is modified, the equalizer curve settings in
Custom1” will be overwritten.
p
If the equalizer curve stored in “Custom1” or “Custom2” is
modified, each stored curve will be overwritten.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 56
2 Touch [Graphic EQ].
3 Select a curve that you want to use as the basis
of customising.
4 Touch the frequency for which you want to
adjust the level.
p If you touch “Custom1” or “Custom2”, recall the equalizer
curve currently stored in “Custom1” or “Custom2”.
p
If you trail a finger across the bars of multiple equaliser
bands, the equaliser curve settings will be set to the value of
the touched point on each bar.
Setting the auto-adjusted equaliser
You can set the auto-adjusted equalizer to suit the vehicle’s
acoustics. To use this function, the Auto EQ measurement must
be done in advance.
Refer to Adjusting the equaliser curve automatically (Auto EQ)
on page 57
The default setting is “Off”.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 56
2 Touch [Auto EQ&TA] to switch “On” or “Off”.
Adjusting the equaliser curve
automatically (Auto EQ)
By measuring the vehicle’s acoustics, the equaliser curve can be
adjusted automatically to suit the vehicle interior.
WARNING
A loud tone (noise) may be emitted from the speakers when
measuring the vehicle’s acoustics. Never perform Auto EQ
measurement while driving.
CAUTION
Thoroughly check the conditions before performing Auto
EQ, as the speakers may be damaged if this is performed
under the following conditions:
When the speakers are incorrectly connected. (For exam-
ple, when a rear speaker is connected as a subwoofer
output.)
When a speaker is connected to a power amp delivering
output higher than the speaker’s maximum input power
capability.
If a microphone for acoustical measurement (sold
separately) is not placed in an appropriate location, the
measurement tone may become loud and measurement
may take a long time, resulting in battery drainage. Be sure
to place the microphone in the specified location.
Before operating the Auto EQ
function
Perform Auto EQ in as quiet a place as possible, with the
vehicle engine and air conditioning switched off. Also, cut
< CRB4880-A >
Audio adjustments
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-EVO1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-EVO1 in the language / languages: English as an attachment in your email.

The manual is 12,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVIC-EVO1

Pioneer AVIC-EVO1 Additional guide - English - 120 pages

Pioneer AVIC-EVO1 Installation Guide - English - 140 pages

Pioneer AVIC-EVO1 Additional guide - German - 120 pages

Pioneer AVIC-EVO1 Installation Guide - German - 140 pages

Pioneer AVIC-EVO1 User Manual - German - 87 pages

Pioneer AVIC-EVO1 Additional guide - Dutch - 120 pages

Pioneer AVIC-EVO1 Installation Guide - Dutch - 140 pages

Pioneer AVIC-EVO1 User Manual - Dutch - 82 pages

Pioneer AVIC-EVO1 Additional guide - French - 120 pages

Pioneer AVIC-EVO1 Installation Guide - French - 140 pages

Pioneer AVIC-EVO1 User Manual - French - 85 pages

Pioneer AVIC-EVO1 Additional guide - Italian - 120 pages

Pioneer AVIC-EVO1 Installation Guide - Italian - 140 pages

Pioneer AVIC-EVO1 Additional guide - Spanish - 120 pages

Pioneer AVIC-EVO1 Installation Guide - Spanish - 140 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info