Manual Pioneer AVH-X490DAB (page 41 of 57) (English)

649374

Zoom out

Zoom in

1/57

remove them in advance. Surrounding sounds may prevent

correct measurement of the vehicle’s acoustics.

 Be sure to use the microphone for acoustical measurement

(sold separately). Using another microphone may prevent

measurement, or result in incorrect measurement of the

vehicle’s acoustics.

 To perform Auto EQ, the front speakers must be connected.

 When this product is connected to a power amp with input

level control, Auto EQ may be impossible if the power amp’s

input level is set below the standard level.

 When this product is connected to a power amp with an LPF

(low pass filter), turn the LPF off before performing Auto EQ.

Also, set the cut-off frequency for the built-in LPF of an active

subwoofer to the highest frequency.

 The distance has been calculated by a computer to provide

optimum delay to ensure accurate results. Do not change

this value.

— The reflected sound within the vehicle is strong and delays

occur.

— The LPF on active subwoofers or external amps delay the

lower sounds.

 If an error occurs during measurement, check the following

before measuring the vehicle’s acoustics.

— Front speakers (left/right)

— Rear speakers (left/right)

— Noise

— Microphone for acoustical measurement (sold separately)

— Low battery

Performing Auto EQ

p Auto EQ changes the audio settings as follows:

— The fader/balance settings return to the centre position.

 Refer to Using fader/balance adjustment on page 38

— “Mute Level” is set to “Off”.

 Refer to Switching sound muting/attenuation on page 38

p Previous settings for Auto EQ will be overwritten.

CAUTION

Do not turn off the engine while the measurement is in

progress.

1 Stop the vehicle in a quiet place, close all the

doors, windows and sun roof, and then turn the

engine off.

If the engine is left running, engine noise may prevent correct

Auto EQ.

p If driving restrictions are detected during measurement,

measurement is cancelled.

2 Fix the microphone for acoustical measurement

(sold separately) in the centre of the headrest

of the driver’s seat, facing forwards.

The Auto EQ may differ depending on where you place the micro-

phone. If desired, place the microphone on the front passenger

seat and perform Auto EQ.

3 Disconnect the iPhone or smartphone device.

4 Turn on the ignition switch (ACC ON).

If the vehicle’s air conditioner or heater is turned on, turn it off.

5 Switch the AV source to “Source OFF”.

 Refer to Selecting a source on page 9

6 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

7 Touch [A-EQ&TA Measurement].

The “A-EQ&TA Measurement” screen appears.

8 Connect the microphone for acoustical meas-

urement (sold separately) with this product.

Plug the microphone into the AUX input jack on this product.

Use an extension cable (sold separately) if the cord of the

Microphone (sold separately) is not long enough.

9 Touch [Front Left] or [Front Right] to select the

current listening position.

10 Touch [Start].

A 10-second countdown starts.

p The Bluetooth connection is disconnected before the pro-

cess starts.

11 Exit the vehicle and keep the doors closed until

the countdown finishes.

When the countdown finishes, a measurement tone (noise)

is emitted from the speakers and the Auto EQ measurement

begins.

12 Wait until the measurement is completed.

When Auto EQ is completed, a message is displayed.

p The measurement time varies depending on the type of

vehicle.

 To stop the measurement, touch [Stop].

13 Store the microphone carefully in the glove box

or another safe place.

If the microphone is subjected to direct sunlight for an extended

period, high temperatures may cause distortion, colour change

or malfunction.

Saving the sound settings

You can save to recall the following current sound settings:

bass boost, slope, subwoofer phase, speaker level, Graphic EQ,

HPF/LPF, listening position, crossover, time alignment.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch [Save Settings].

3 Touch [OK].

All of the current sound settings are saved.

 When you touch [Cancel], return to the “Audio”

setting screen.

Loading the sound settings

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch [Load Settings].

3 Touch the item.

The following items are available:

AEQ Setting,Sound Setting.

p “AEQ Setting” is available only when you have already

performed Auto EQ measurement.

 Refer to Adjusting the equaliser curve automatically (Auto EQ)

on page 40

p “Sound Setting” is available only when you have already

saved the sound settings.

 Refer to Saving the sound settings on page 41

< QRB3687-A >

Audio adjustments

I have a awhx490 I cant get the dab radio to tune in ...
Its says no signal.. on it's on. Hz not FM... so cant get radio 2
Please help..its on our moterhome cd works and bluetooth... Submitted on 6-3-2022 at 14:20
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVH-X490DAB in the language / languages: English as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVH-X490DAB

Pioneer AVH-X490DAB Installation Guide - English, German - 48 pages

Pioneer AVH-X490DAB User Manual - German - 63 pages

Pioneer AVH-X490DAB Installation Guide - Dutch - 48 pages

Pioneer AVH-X490DAB User Manual - Dutch - 62 pages

Pioneer AVH-X490DAB Installation Guide - French - 48 pages

Pioneer AVH-X490DAB User Manual - French - 61 pages

Pioneer AVH-X490DAB Installation Guide - Italian, Spanish - 48 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer AVH-X490DAB Manual

Product: