649371
3
Zoom out
Zoom in
Previous page
1/48
Next page
3
This product
1
2
3
45
789
6
acb
1 Pioneer navigation system
Please contact your dealer to inquire about the connectable
navigation unit.
2
RGB cable(supplied with Navigation system)
3 Microphone 4 m
4 This product
5 Wired remote input
Hard-wired remote control adapter can be connected (sold
separately).
6
Digital Radio aerial input
(AVH-X5800DAB) (AVH-X3800DAB)
7
Aerial jack
8 Power supply
9 Fuse (10 A)
a Front output (STD)/High range output (NW)
b Rear output (STD)/Middle range output (NW)
c SubWoofer output (STD)/Low range output (NW)
Power cord
1. 2.
1
3
2*
2
4
1*
5
4*
6
3*
b (6*)
8
9
a (5*)
7
c
d
e
f
g
lk
h
j
i
1 To power supply
2 Depending on the kind of vehicle, the function of 2* and 4*
may be different. In this case, be sure to connect 1* to 4*
and 3* to 2*.
3
Yellow (2*)
Back-up (or accessory)
4
Yellow (1*)
Connect to the constant 12 V supply terminal.
5
Red (4*)
Accessory (or back-up)
6
Red (3*)
Connect to terminal controlled by ignition switch (12 V DC).
7
Connect leads of the same colour to each other.
8 Orange/white
To lighting switch terminal.
9
Black (earth)
To vehicle (metal) body.
a
Blue/white (5*)
The pin position of the ISO connector will differ depending
on the type of vehicle. Connect 5* and 6* when Pin 5 is an
aerial control type. In another type of vehicle, never connect
5* and 6*.
b
Blue/white (6*)
Connect to auto-aerial relay control terminal (max. 300 mA
12 V DC).
c
Blue/white
Connect to system control terminal of the power amp (max.
300 mA 12 V DC).
d
Violet/white
Of the two lead wires connected to the back lamp, connect
the one in which the voltage changes when the gear shift
is in the REVERSE (R) position. This connection enables
the unit to sense whether the car is moving forwardss or
backwardss.
e
Yellow/black
If you use an equipment with Mute function, wire this lead
to the Audio Mute lead on that equipment. If not, keep the
Audio Mute lead free of any connections.
f
Light green
Used to detect the ON/OFF status of the handbrake. This
lead must be connected to the power supply side of the
handbrake switch.
g
Connection method
1 Clamp the lead.
2 Clamp firmly with needle-nosed pliers.
h Power supply side
i Handbrake switch
j Earth side
k Speaker leads
White: Front left + or high range left +
White/black: Front left – or high range left –
To prevent damage
WARNING
Use speakers over 50 W (maximum input power) and
between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω
to 3 Ω speakers for this unit.
The black lead is earth. Please earth this lead
separately from the earth of high-current products
such as power amps. Do not earth more than one
product together with the earth from another product.
For example, you must separately earth any amp
unit away from the earth of this product. Connecting
earths together can cause a fire and/or damage the
products if their earths became detached.
When replacing the fuse, be sure to only use a fuse of
the rating prescribed on this product.
This product cannot be installed in a vehicle without ACC
(accessory) position on the ignition switch.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
To avoid short-circuiting, cover the disconnected lead with
insulating tape. It is especially important to insulate all
unused speaker leads, which if left uncovered may cause a
short circuit.
For connecting a power amp or other devices to this product,
refer to the manual for the product to be connected.
Notice for the blue/white lead
When the ignition switch is turned on (ACC ON), a control
signal is output through the blue/white lead. Connect to an
external power amp’s system remote control terminal, the
auto-aerial relay control terminal, or the aerial booster power
control terminal (max. 300 mA 12 V DC). The control signal is
output through the blue/white lead, even if the audio source
is switched off.
3
< CRD4923-B >
Connection Connection
3


Need help? Post your question in this forum.

Forumrules
1

Forum

pioneer-avh-x2800bt

Reset search

  • radio won’t stop scrolling after install a back up camera what am I supposed to do to stop it Submitted on 28-5-2020 at 23:44

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVH-X2800BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVH-X2800BT in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVH-X2800BT

Pioneer AVH-X2800BT User Manual - English - 57 pages

Pioneer AVH-X2800BT User Manual - German - 63 pages

Pioneer AVH-X2800BT User Manual - Dutch - 62 pages

Pioneer AVH-X2800BT User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info