651675
14
Zoom out
Zoom in
Previous page
1/116
Next page
06 Additional information
14
En
Chapter 6:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
Problem Remedy
The power does not turn on. • Is the power plug disconnected from the power outlet? Connect the power plug
correctly to its outlet (page 7).
•Is the power cord disconnected from the AC IN connector? Connect the power cord
correctly (page 7).
Power turns off. •Is the Auto Power Down function turned ON? If you do not want the power to turn off
automatically, disable the Auto Power Down function (page 12).
The power turned off and the
STANDBY/APD
indicator is flashing
three times repeatedly.
•The protection circuit has been activated. This condition will result if a very low-
frequency sound is played at a high sound volume level.
- Turn the power OFF and wait for at least one minute, then turn the power ON again;
play the music at a lower sound volume level.
- After restarting the power, if the
STANDBY/APD
indicator flashes four times, it
indicates the receiver channels are malfunctioning. Disconnect the power cord and
consult your dealer or nearest Pioneer service station.
The power turned off and the
STANDBY/APD
indicator is flashing
once every two seconds.
•The unit’s internal temperature has risen and the safety circuit has operated.
- Turn power OFF and wait for a minute or more, allowing the unit’s temperature to
cool before turning the power ON again.
- Install the unit in a location with better ventilation.
- Confirm that the unit is installed correctly; if the unit is turned on again without
being allowed to cool, the same symptoms may appear (page 4).
The power turned off and the
STANDBY/APD
indicator is flashing
twice repeatedly.
•Are you using speakers with impedance values not supported by this unit? Confirm
the speaker’s nominal impedance value (page 6).
•Are any speaker cables loose from the
SPEAKERS
terminals and touching other
wires or the surface of the rear panel? Disconnect the power cord and reconnect the
speaker cables correctly (page 6).
The power turned off and the
STANDBY/APD
indicator is flashing
six times repeatedly.
•The protection circuit has been activated. This condition will result if a very high-
frequency sound is played at a high sound volume level.
- Lower the sound volume and try playing again.
- If the same symptom appears when the power is turned OFF then ON again, the
unit’s circuitry may be damaged. Disconnect the power cord and consult your
dealer or nearest Pioneer service station.
The
STANDBY/APD
indicator is
flashing four times, five times, or
seven times repeatedly and the power
does not turn on.
•The unit’s circuitry is damaged. Disconnect the power cord and consult your dealer
or nearest
Pioneer authorized service center
.
No sound is output when a function is
selected.
•A connection cable is disconnected or connected improperly. Check your
connections (page 5).
•Connectors or pin plugs on a cable are dirty. Wipe off any dirt from connectors and
pin plugs.
•Confirm that the unit’s input selector is set to the desired playback component. Set
selector correctly (page 11).
•Press
MUTE
on the remote control to turn muting off (page 10).
No sound from one speaker. •Are the connection cables or speaker cables disconnected on one side? Reconnect
securely (page 5).
Can’t operate the remote
control.
•Replace the battery (page 4).
•Operate within 7 m, 30° of the remote sensor on the front panel (page 4).
•Remove the obstacle or operate from another position.
•Avoid exposing the remote sensor on the front panel to direct light.
•Is the control cord for one component connected improperly? Confirm correct
connections (page 7).
Can’t change input source. •Check whether
POWER AMP DIRECT
function is ON. If so, press the front panel’s
POWER AMP DIRECT
button to turn the function OFF (page 11).
Sound of the digital input is not
output.
•The digital format of the output device is not supported. If the output device is set to
an audio signal (Dolby Digital, DTS, etc.) other than PCM, change the setting to PCM.
Sound of the digital input is not output
when playing back a SACD.
•Many SACD players (including Blu-ray players and DVD players compatible with
SACD playback) are not designed to output digital when playing back a SACD. Check
the specifications of the SACD player. Alternatively, play back the audio with an analog
connection.
No sound is heard when a linear PCM
signal with frequency of 96 kHz or
more is input to the
DIGITAL IN
COAXIAL
terminal.
•Sound may not be output properly depending on the digital coaxial cable used; try
replacing the cable (sold separately) with another.
Problem Remedy
A70_SYXE8_0728.book 14 ページ 2015年7月28日 火曜日 午後3時54分
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer A-50DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer A-50DA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 23,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info