699650
21
Zoom out
Zoom in
Previous page
1/72
Next page
21
Others
En
Problems may be solved by simply turning the power on/off
or disconnecting/connecting the power cord, which is easier
than working on the connection, setting and operating
procedure. Try the simple measures on both the unit and the
connected device. After reconnecting, turn off and on the
unit and the connected device.
0 This unit contains a microPC for signal processing and
control functions. In very rare situations, severe
interference, noise from an external source, or static
electricity may cause it to lockup. In the unlikely event that
this happens, unplug the power cord from the wall outlet,
wait at least 5 seconds, and then plug it back in.
0 We are not responsible for reparations for damages (such
as CD rental fees) due to unsuccessful recordings caused
by the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
Resetting the unit (this resets the unit settings
to the default)
Resetting the unit to the status at the time of shipment may
solve the problem. If the unit is reset, your settings are
restored to the default values. Be sure to note down your
setting contents before performing the following operations.
1. While the power is on, press Í STANDBY/ON while
pressing DIRECT.
Cannot turn on the unit
0 Make sure that the power cord is properly plugged into
the wall outlet.
0 Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
The unit turns off unexpectedly
0 The unit automatically enters standby mode when auto
standby (p20) is activated.
0 A speaker cable may have shorted and the protective
circuit function may have been activated. Make sure bare
speaker wires are not touching each other or the back
panel of the unit, then turn the unit on again. If this unit
does not turn on, immediately unplug the power cord from
the wall outlet and contact your dealer.
0 The protective circuit function may have been activated
because the temperature of the unit rose abnormally. If
this happens, then the power will continue to turn off after
you have turned the unit on again. Make sure the unit has
plenty of space for ventilation around it, wait for the unit to
cool down sufficiently, and then try turning it on again.
0 When switched to power amplifier mode, if the volume of
the connected pre-amplifier is low, auto standby (p20)
may function and the power may automatically switch to
standby. If this happens, you may be able to fix it by
increasing the volume on the pre-amplifier.
WARNING: If smoke, smell or abnormal noise is produced
by the unit, unplug the power cord from the wall outlet
immediately and contact the dealer or customer support.
0 Confirm that the connection between the output jack on
the device and the input jack on this unit is correct.
0 Make sure that none of the connecting cables are bent,
twisted, or damaged.
0 If MUTE is active, press MUTE on the remote controller to
cancel. MUTE is active when the SPEAKERS indicator
and the indicator for the selected input source are
blinking.
0 While headphones are connected to the PHONES jack,
no sound is output from the speakers.
Audio performance
0 Audio performance will be at its best about 10 to 30
minutes after the integrated amplifier has been turned on
and had time to warm up.
0 The sound quality can be affected by strong magnetic
fields, such as those from a TV. Try moving any such
devices away from the integrated amplifier.
0 If you have any devices that emit high-intensity radio
waves near the integrated amplifier, such as a cellular
phone that’s being used to make a call, the integrated
amplifier may output noise.
0 Install the integrated amplifier on a sturdy rack or shelf.
Position it so that its weight is evenly dispersed on its four
insulators. Do not install the integrated amplifier in a place
with vibration or an unstable location.
No sound from a connected playback device
0 Change the input selector on this unit to the position of
the terminal to which the playback device is connected.
0 Only PCM audio is supported for input through the
DIGITAL IN OPTICAL/COAXIAL jacks. Set the audio
output on the playback device to output PCM.
A speaker produces no sound
0 Make sure that the polarity of the speaker cables (+/-) is
correct, and that no bare wires are in contact with the
metal part of speaker terminals.
Before starting the procedure
Power
1
2
Audio
SN29403415_A-40AE_En_1804XX.book 21 ページ 2018年5月23日 水曜日 午後3時19
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer A-40AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer A-40AE in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer A-40AE

Pioneer A-40AE User Manual - German, Dutch, Italian, Swedish - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info