643476
12
Zoom out
Zoom in
Previous page
1/64
Next page
In determining optimum vent termination, carefully evaluate external
conditions especially when venting directly through a wall. Since you
must deal with odors, gases, and y ash, consider aesthetics, prevailing
winds, distances from air inlets and combustibles, location of adjacent
structures and any code requirements.
•Exhaust must terminate above combustion air inlet elevation.
•Do not terminate vent in any enclosed or semi-enclosed area, (i.e.
Carports, garage, attic crawl space, etc.) or any location that can build
up a concentration of fumes.
•Terminals must not to be recessed into a wall or siding.
•When setting into place ue caps you should consider wind factors
such as dominate wind directions and currents in order to avoid down
draft, y ash and/or smoke.
a Vent surfaces can get hot enough to cause burns if touched
by children.
Non-combustible shielding or guards may be required.
a Be sure to use approved pellet vent pipe and wall pass-
through ttings to go through combustible materials.
The type of installation must rst be considered before determining
the exact location of the venting termination in relation ship to doors,
window, cavities or air vents. See gures 18-19.
Without outside combustion air connected to the unit.
For These types of installations please refer to the dimensions listed in
gure 18.
The clearance to a door, window or cavity must be at least:
- 4’ (1.2 m) below;
- 4’ (1.2 m) horizontally;
- 1’ (305 mm) above.
The clearance to fresh air intake for combustion of the pellet stove
or any other appliance, or the non-mechanical air supply inlet to the
building must be at least 4’ (1.2 m).
The clearance to a mechanical air supply inlet to the building must be
at least 10’ (3 m).
With outside combustion air connected to the unit.
For These types of installations please refer to the dimensions listed in
gure 19.
DT0000000-00
1.12 vENTING: TERMINATION REqUIREMENTS
FRESH AIR
INTAKE
MECHANICAL
AIR SUPPLY INLET
4'
1'
4'
4' 10'
1'
A = EXHAUST TERMINAL
A
A
4'
9"
1,5'
1,5'
4'
9"
1,5'
8'
FRESH AIR
INTAKE
MECHANICAL
AIR SUPPLY
INLET
A = EXHAUST TERMINAL
A
A
A
A
A
Fig. 18
Fig. 19
This conguration will help prevent blockage of vent by snow drifts. Also the minimum vertical run of 5 feet (1,5 m) ensures the ventilation of the
exhaust in the event of a power failure, and allow for easier cleaning through cleanout on tee.
a Certain local code restrictions may apply. Check with Local Ofcials rst before installing.
a Strictly observe the PL Vent manufacturer’s safety specications when using wall pass through.
a INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
a Double wall PL vent requires a minimum clearance to combustibles according to the manufacturer’s safety specications and the use
of listed wall thimble, re stop or roof ashing where applicable.
a Do not place joints within wall pass-throughs.
a Ensure that all installation work is carried out to professional standards.
H07028100/DT2000970 – 01
12
English
DT2033048-00
DT2033047-00
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Piazzetta P960 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Piazzetta P960 in the language / languages: English as an attachment in your email.

The manual is 2,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info