The pellet stove is tted with the Multicomfort function. This works in conjunction with the Multifuoco ventilation system to improve heat distribution.
It allows the room temperature to be read from the stove or from the remote control, so that the Multifuoco settings can be varied according to the
requirements of the rooms to be heated.
If the airow from your stove has been ducted to other rooms you may read the temperature in the room where the stove is installed or in the room
where the remote control is situated.
Example: your stove is installed in a small room and you are ducting the heat only from the rear of the stove (see solution 1 under the paragraph
“MULTIFUOCO SYSTEM”). You can position the remote control in the room to where the hot air has been ducted and set the required temperature
from this room. To carry out the necessary settings see the MULTICOMFORT menu.
MULTICOMFORT
This function is used to choose the sensor for reading the room temperature: from the stove or from the remote control. To make the
most of the Multifuoco fan functions read the paragraphs MULTIFUOCO SYSTEM and MULTICOMFORT OPERATION.
Function ActionDisplay
Select the
MULTICOMFORT
menu
Press the MENU key, then using the SELECT MENU key select the
MULTICOMFORT menu.
Conrm by pressing the SET key.
MULTI
COMFORT
SELECT
RRC
SELECT
STOVE
1
1
1
Select the REMOTE
CONTROL SENSOR
(SELECT RRC) or
STOVE (SELECT
STOVE)
Press the SELECT MENU key and select “SELECT RRC” to read the room
temperature from the remote control or “SELECT STOVE” to read the
room temperature from the stove. Conrm by pressing the SET key. After
conrmation the readout function enabled (FUNCTION ENGAGED) will
appear on the display and the remote control will automatically return to
the initial display.
MULTI
COMFORT
SELECT
RRC
SELECT
STOVE
1
1
1
MULTI
COMFORT
SELECT
RRC
SELECT
STOVE
1
1
1
DT2040070-04
DT2012431-00
6.13 ENERGY SAVING
When the ENERGY SAVING mode is enabled, automatic startup/ignition and shutdown of the stove is activated at temperature values set by the user
through the STOP and START functions.
The temperature value selected 2, 4 or 6 °F (1, 2 or 3 °C ) in STOP function or selected in START function with negative values -2, -4 or -6 °F (-1, -2
or -3 °C) denes the value from which the Energy Saving mode will either increment or deduct from the room temperature set.
The operating principle is as follows:
when the room temperature measured by the room sensor or the remote control reaches the temperature value programmed by the user, the stove
automatically goes to power level 1 (readout “OK” on the display).
If the room temperature continues to rise with operation at power level 1 up to the value set on the STOP function (e.g. +4 °F / +2 °C compared to
the programmed temperature), the stove shuts down and goes into the stand-by mode.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Piazzetta P958 M at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Piazzetta P958 M in the language / languages: English as an attachment in your email.
The manual is 5,07 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
