698651
6
Zoom out
Zoom in
Previous page
1/24
Next page
6
7
SOSTITUZIONE SENSORE / REPLACING SENSOR
REMPLACEMENT SENSEUR / SENSOR - AUSTAUSCH
(COD. VM372)
In caso di sostituzione il sensore necessita anche di una programmazione, procedere come segue:
1 - Attendere 25 secondi dopo aver attivato il sistema. Premere 5 volte il pulsante remoto per visualizzare il
programma.
2 - Premere il pulsante remoto per posizionarsi sul pneumatico interessato.
3 - Installare il nuovo sensore.
4 - Il sistema riceverà il segnale del sensore e visualizzerà i valori. Premere brevemente il pulsante remoto
per confermare.
5 - Una volta terminata la programmazione tenere premuto il pulsante per salvare i dati.
6 - Il sistema visualizzerà lo stato dei pneumatici sul display.
When you replace a sensor, programming will be necessary, as follows:
1 - Activate system and wait for 25 seconds. Press remote-key 5 times, to visualize the program.
2 - Press remote-key to position yourself on the tyre in question.
3 - Install the new sensor.
4 - The system will receive the sensor-signal and show the values. Briey press the remote-key to conrm.
5 - When programming is complete, keep remote-key pressed, to memorize the Data.
6 - The system will show the tyre-status on the display.
En cas de substitution, le senseur nécessite aussi d’une programmation, pour cela, suivre la procédure ci-dessous:
1 - Attendre 25 secondes après avoir activé le système. Appuyer 5 fois le bouton remote pour visualiser.
Programme
2 - Appuyer le bouton remote pour se positionner sur le pneu concerné.
3 - Installer le nouveau senseur.
4 - Le pneu recevra le signal du senseur et visualisera les valeurs. Appuyer brièvement sur le bouton remote
Pour valider.
5 - Une fois terminée la programmation, faire pression sur le bouton pour sauvegarder les données.
6 - Le système visualisera l’état des pneus sur l’acheur.
Immer wenn ein Sensor ausgetauscht wird, muss dieser auch wie folgt programmiert werden:
1 - Nach Aktivierung des Systems, 25 Sekunden warten. Remote-Taste 5 Mal drücken, um das Programm auszuwei-
sen.
2 -Remote-Taste drücken, um auf den gewünschten Reifen zu gehen.
3 - Neuen Sensor installieren.
4 - Das System bekommt das Sensor-Signal zugestellt und weist die erfassten Werte aus. Zur Bestätigung, Remote-
Taste kurz drücken.
5 - Bei beendeter Programmierung, Remote-Taste gedrückt halten, damit die Daten eingespeichert werden.
6 - Das System sorgt für die Ausweisung der Reifen-Situation auf dem Display.
IT GB
FR D
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Phonocar VM362 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Phonocar VM362 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info