698652
10
Zoom out
Zoom in
Previous page
1/20
Next page
10
11
Handel als volgt - Følg den nedenstående fremgangsmåde - Postępować w następujący sposób
Postupujte následovně
(COD. VM372)
MĚNA SENZORU
Pětkrát stiskněte tlačítko , displej vydá akustický signál –pípnutí.
Pro zvolení pneumatiky, kterou chcete programovat, stiskněte tlačítka .
Jakmile se zobrazí nová hodnota, pro uložení stiskněte tlačítko .
Pro naprogramování
dalšího snímače stiskněte tlačítko
nebo stiskněte .
Po naprogramování podržte tři sekundy stisknuté tlačítko .
Vyměňte snímač a pneumatiku částečně vyfoukněte.
Po naprogramování podržte tři sekundy stisknuté tlačítko
pro opuštění režimu nastavení. Hranice alarmu nízkého
a vysokého tlaku musí být nastaveny na hodnotu o cca 20–25 % nižší nebo vyšší, než je hodnota uvedená výrobcem
(viz str. 17-18)
Pokud operace neprovedete do tří minut, displej se vrátí do režimu monitorování.
WYMIANA CZUJNIKA /
Nacisnąć pięciokrotnie klawisz , wyświetlacz wyemituje sygnał dźwiękowy “beep”.
Nacisnąć klawisze , aby wybrać oponę, która będzie programowana.
Po wyświetleniu nowej wartości nacisnąć klawisz
, aby zapisać.
Nacisnąć klawisz
lub , aby zaprogramować inny czujnik.
Po zakończeniu programowania, aby zatwierdzić, nacisnąć klawisz
przez 3 sekundy.
Wymienić czujnik, spuszczając częściowo powietrze z opony.
Po zakończeniu programowania przytrzymać naciśnięty klawisz
przez 3 sekundy, aby wyjść z trybu ustawień.
Progi alarmowe niskiego i wysokiego ciśnienia należy ustawić na wartość niższą lub wyższą o ok. 20%-25% wartości
wskazanej przez producenta (zob. str. 17-18)
Jeśli w ciągu 3 minut nie zostanie wykonana żadna czynność, wyświetlacz powróci do trybu monitorowania.
UDSKIFTNING AF SENSOR
Tryk på knappen i fem gange, displayet udsender en “bip lyd.
Tryk på knapperne
for at vælge dækket til programmering.
Når den nye værdi vises, tryk på knappen
for at gemme.
Tryk på knappen
eller tryk på for at programmere en anden føler.
Efter at programmeringen er afsluttet, tryk på knappen
i tre sekunder for at bekræfte.
Udskift føleren ved at lukke lidt luft ud fra dækket.
forhold til værdien angivet af fabrikanten (jvf. side 17-18)
Hvis intet indgreb gennemføres i løbet af tre minutter, vender displayet tilbage til overvågningsfunktion.
VERVANGING SENSOR /
Druk vijf keer op de toets , het display zal een “pieptoon laten klinken.
Druk op de toetsen
om de te programmeren band te selecteren.
Druk, wanneer de nieuwe waarde weergegeven wordt, op de toets
om
deze op te slaan.
Druk op de toets of druk op om een andere sensor te programmeren.
Is programmering beëindigd, druk dan drie seconden op de toets om te bevestigen.
Vervang de sensor door de band gedeeltelijk te laten leeglopen.
NL DA
PL CZ
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Phonocar VM361 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Phonocar VM361 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info