Manual Phoenix SS0801K (page 2 of 2) (English, German, French, Italian, Spanish)

737116

Zoom out

Zoom in

1/2

SS0800K/KD INSTRUCTIONS &

GUARANTEE REGISTRATION

SS0800K/KD ISTRUZIONI & REGISTRAZIONE

GARANZIA

SS0800K/KD BEDIENUNGSANLEITUNG UND

GARANTIEREGISTRIERUNG

1. An electric drill

2. 1 masonry drill bit -12mm

3. Adhesive tape

4. A pencil

5. A ruler

6. A 13mm socket

HOW TO BOLT YOUR SAFE DOWN –

YOU WILL REQUIRE

CHOOSING A PLACE TO INSTALL YOUR SAFE

1. Look for a place that does not restrict access and the swing of the door.

2. Ensure that the floor is level.

3. For best results a concrete floor is preferable.

DRILLING & BOLTING

1. Manoeuvre the safe into the required position. Now with the pencil mark the floor around the safe

(If the safe is against a wall then just the front and sides needs to be marked）

2. Open the safe door.

3. Using the pencil, mark the positions on the floor for drilling through the base fixing holes in the base

of the safe.

4. Now move the safe to one side, giving you access to the markings on the floor.

5. Before using the drill bit. With the ruler measure 46mm from the tip of the bit and put a piece of

adhesive tape around the bit to ensure you do not drill too deep.

6. Drill the 12mm holes in the floor until you reach your 46mm marker.

7. Clean the floor around the holes.

8. There are three parts to your bolts

a. A coach screw

b. A plastic expanding sleeve

c. A steel washer

9. Insert the plastic expanding sleeves into the drilled holes.

10. Place the safe back into position, insert the coach screws, including the washers, through the base

of the safe, into the floor and tighten until you can not tighten them any further.

YOUR SAFE IS NOW BASE FIXED.

Thank you for purchasing a Phoenix Safe.

OPENING SAFE

Please insert one of the two keys supplied into the key hole and turn clockwise.

Then pull the door to open.

Your safe is ready prepared for base fixing. To base fix your safe, follow the instructions below.

Version 1/PB/APR 16

1. 1 Bohrmaschine

2. 1 x 12mm Bohrer

3. Klebeband

4. 1 Bleistift

5. 1 Lineal

6. 1 x 12mm Schraubenschlüssel

-BODENVERANKERUNG DES TRESORS-

SIE BENÖTIGEN:

DIE AUSWAHL DES STANDORTES FÜR IHREN TRESOR

1. Suchen Sie sich einen Platz aus, an dem das Öffnen der Tresortür durch nichts beeinträchtigt wird

(Türradius).

2. Vergewissern Sie sich, dass der Boden gerade / eben ist.

3. Am besten ist ein Betonboden.

BOHREN & BEFESTIGEN

1. Stellen Sie den Tresor auf die gewünschte Position. Nun markieren Sie mit einem Bleistift die

äußeren Abmessungen des Tresors auf dem Boden (wenn der Tresor an der Wand steht, markieren

Sie bitte nur die Front und die beiden Seiten)

2. Öffnen Sie die Tresortür.

3. Markieren Sie die Bohrlöcher auf dem Fußboden. Benutzen Sie hierfür den Bleistift.

4. Entfernen Sie nun den Tresor, sodass die Markierungen auf dem Fußboden zu sehen sind.

5. Bevor Sie den 12mm Bohrer benutzen, messen Sie mit einem Lineal 46mm von der Bohrerspitze ab

und markieren Sie diese Stelle mit Klebeband, um sicher zu stellen, dass Sie nicht zu tief bohren.

6. Bohren Sie die 12mm Löcher in den Fußboden und achten Sie darauf, dass Sie nicht tiefer als 46mm

bohren.

7. Entfernen Sie jetzt die Bohrspäne und reinigen Sie den Fußboden

8. Ein Befestigungsset besteht aus 4 Teilen:

a. einer Sechskantschraube

b. einer Unterlegscheibe

c. einem Metalldübel

d. einem „Metallkeil“

9. Positionieren Sie den Tresor erneut, stecken Sie die kompletten Schrauben vom Tresorinneren durch

die Bohrungen und ziehen diese dann mit dem Schraubenschlüssel fest.

IHR TRESOR IST NUN IM BODEN VERANKERT.

Vielen Dank, dass Sie sich für einen Tresor aus dem Hause Phoenix entschieden haben.

ÖFFNEN DES SAFES

Einen der beiden mitgelieferten Schlüssel in das Schlüsselloch stecken und im Uhrzeigersinn drehen.

Dann am Türgriff ziehen um den Tresor zu öffnen.

Ihr Tresor ist bereits für die Bodenmontage vorbereitet. Bitte folgen Sie den unten stehenden

Anleitungen.

1. Un trapano elettrico.

2. Una punta da trapano per edilizia -12mm

3. Nastro adesivo

4. Una matita

5. Un righello

6. Una chiave da 13mm

COME ANCORARE LA CASSAFORTE –

MATERIALE NECESSARIO

SCHEGLIERE IL LUOGO PER INSTALLARE LA CASSAFORTE

1. Scegliere un luogo che non causi restrizioni di accesso e permetta l’apertura dello sportello.

2. Assicurarsi che il pavimento sia piano.

3. Un pavimento in cemento è ottimale.

FORARE & ANCORARE

1. Collocare la cassaforte nella posizione desiderata. Con la matita tratteggiarne la sagoma sul

pavimento. (Se la cassaforte è appoggiata alla parete, basterà tracciare la parte laterale e frontale)

2. Aprire lo sportello della cassaforte.

3. Con la matita contrassegnare sul pavimento la posizione dei fori da praticare attraverso la base della

cassaforte.

4. Quindi spostare la cassaforte in modo da avere accesso ai contrassegni sul pavimento.

5. Prima di usare la punta da trapano: con il righello misurare 46mm dall’apice della punta ed

applicare un pezzo di nastro adesivo attorno alla punta in modo da non praticare fori troppo

profondi.

6. Praticare fori da 12mm nel pavimento fino a raggiungere la profondità di 46mm.

7. Pulire il pavimento intorno ai fori.

8. I bulloni sono composti da 3 parti:

a. Una vite

b. Un tassello ad espansione in plastica

c. Una rondella in acciaio

9. Inserire i tasselli in plastica nei fori praticati

10. Riposizionare la cassaforte, inserire le viti, comprese le rondelle, attraverso i fori nella base della

cassaforte, nel pavimento, e stringere saldamente.

LA CASSAFORTE È ORA ANCORATA AL PAVIMENTO.

Grazie per aver acquistato una Cassaforte Phoenix.

APRIRE LA CASSAFORTE

Inserire nella serratura una delle due chiavi in dotazione e girare in senso orario.

Quindi tirare lo sportello per aprire.

La cassaforte è pronta per essere fissata alla base. Per fissare la cassaforte alla base seguire le istruzioni

sotto indicate.

REGISTRAZIONE DELLA GARANZIA

Per una maggiore sicurezza vi raccomandiamo di inoltrare la vostra

registrazione della garanzia visitando il nostro sito web: www.phoenixsafe.com

e cliccando su registrazione della garanzia.

VIA MONTE ROSA 28, 20049, CONCOREZZO, MILAN, ITALY | 39 039 5965844

GUARANTEE REGISTRATION

Please submit your guarantee registration by visiting our website

www.phoenixsafe.com and clicking on guarantee registration.

For further assistance or information please contact us on 0151 944 6444.

APEX HOUSE, 1 ORRELL MOUNT, LIVERPOOL, L20 6NS,

UNITED KINGDOM | +44 (0)151 944 6444

GARANTIEKARTE

Aus Sicherheitsgründen empfehlen wir Ihnen, Ihre Garantiekarte online auf

unserer Website www.phoenixsafe.com per Mausklick auf der Schaltfläche

„Garantieanmeldung“ auszufüllen.

DEUTSCHLAND GMBH, BAHNSTR. 23, D-42327 WUPPERTAL

0049-202-69519-0

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Phoenix SS0801K in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Phoenix SS0801K Manual

Product: