492033
5
Zoom out
Zoom in
Previous page
1/8
Next page
© 2010 Phoenix Gold • www.phoenixgold.com
Amplier Owners Manual
Power Output:
RMS Power 16.0Vdc 8000 x 1 @ 2 ohm
12000 x 1 @ 1 ohm
24000 x 1 @ 2 ohm (Strapped)
RMS Power 14.4Vdc 5000 x 1 @ 2 ohm
8000 x 1 @ 1 ohm
16000 x 1 @ 2 ohm (Strapped)
SPL “Burping” Power 16.0Vdc 10000 x 1 @ 2 ohm
18000 x 1 @ 1 ohm
36000 x 1 @ 2 ohm (Strapped)
INPUT
Connect preamp signal cables from the head unit to these terminals.
OUTPUT
Provides a full range signal for an additional amplier. There is no signal
loss if using this output.
LP FREQ
Controls the lowpass crossover point for the speaker outputs.
BASS BOOST
Variable bass boost from 0 to +6dB @ 45 Hz.
LOW PASS LEVEL CONTROL (LPL)
This port is for connecting the optional remote level control (LPL44).
This allows up to 20dB of volume adjustment. This is not a bass boost, it
controls the level of the low pass signal.
LEVEL
Used to reach maximum amplier power with a wide variety of headunits.
SPEAKER OUTPUTS
Used to connect the amplier to speakers. Minimum impedance is 1 ohm. 8 gauge
wire is required.
SUBSONIC
Controls the subsonic (highpass) crossover point for the speaker outputs to eliminate
extreme low frequencies.
PROTECT LED
Lights red if there is a problem with the audio system. For example, speaker wire is
pinched/shorted together or the amplier is running too low of an impedance.
INPUT SLAVE/OUTPUT MASTER SWITCH
For normal use, the switch MUST be set to OUTPUT MASTER”. If linking or strapping
two ampliers together please see page 7 for more details. IMPORTANT: In normal or
single amplier use there will be no output if this switch is set to “INPUT SLAVE”. Be
sure it is set to “OUTPUT MASTER”.
+12V
This must be connected to the fused positive terminal (+12V) of the cars battery. See
page 4 for an electrical system example. 1/0 gauge wire is required.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming from the head
unit or ignition.
GND
This must be connected to the negative terminal of the car’s battery or bolted to a
clean, unpainted part of the chassis of the vehicle. 1/0 gauge wire is required.
COntrols
REMOTE MONITORING DISPLAY (RMD)
Connect optional RMD Voltage Display to this port.
IMPORTANT: ALL THREE POWER TERMINALS MUST
BE USED. DO NOT USE ONLY ONE OR TWO OF THE
TERMINALS, IT CAN DAMAGE THE AMPLIFIER.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Phoenix Gold The one at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Phoenix Gold The one in the language / languages: English as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info