811249
12
Zoom out
Zoom in
Previous page
1/24
Next page
12 Philips · Screeneo U4
Bluetooth connection
The projector is equipped with Dual Bluetooth
5.0 technology, allowing you to connect to
up to 2 speakers or sets of headphones. You
can independently control the volume of each
connected device.
Before you can use the projector with Bluetooth
speakers or headphones for the first time, you
must pair the projector with them. The projector
will automatically connect to a device as soon
as they are paired.
Notice
Be sure that the Bluetooth device is
no farther than 10 m (33 ft) from the
projector when connecting the two.
Even when connecting within the
specified communication distance,
connections can be lost due to the signal
status.
Pairing
Speaker/Headphones 1 Speaker/Headphones 2
ON
13
2
4
1 Make sure the projector is on.
2 Turn on your Bluetooth speaker or
headphones and make sure it is in pairing
mode. Press the pairing button on the
device, if needed. See the documentation
supplied with the device for more
information.
3 Press either of the buttons on the
projector to pair the projector with the
device.
Once you press this button, the
projector enters pairing mode and
displays "Searching" on the screen.
Also, its power LED blinks in light blue.
When the pairing is complete, the
projector briefly displays "Paired
successfully" on the screen, as well as
the name of the paired device. Also, its
power LED turns solid light blue.
If no pairing is created, the projector will
automatically exit pairing mode in 10
seconds.
4 To pair a second Bluetooth speaker or set
of headphones, repeat steps 2 and 3 above
but press the other button in step 3.
Tips:
The projector will automatically switch its
audio output to Bluetooth output after
connecting to a Bluetooth device.
After connecting a Bluetooth device,
press / on the remote control to
adjust the volume to the desired level. To
independently control the volume of each
connected device, use the volume control
of that device.
Disconnect a Bluetooth device
Use one of the following methods to disconnect
a Bluetooth device from the projector but leave
it paired.
The projector automatically switches its audio
output to internal speaker when no Bluetooth
device is connected.
Terminate the Bluetooth connection
from the Bluetooth device, or turn off the
Bluetooth device. The projector will briefly
display "Disconnected" on the screen.
Turn off the projector.
Reconnect a Bluetooth device
Once you pair and connect a Bluetooth
device to the projector using the steps above,
the projector will automatically reconnect
unless the Bluetooth device gets unpaired
or turned off. The projector briefly displays
"Paired successfully" on the screen after a
reconnection.
Unpair a Bluetooth device
This will remove the Bluetooth device from the
projector's memory. You'll need to pair and
connect this device to use it again.
To unpair a Bluetooth device, press and hold
the corresponding button on the projector for
3 seconds while the device is connected. The
projector briefly displays "Disconnected" on the
screen after the unpairing.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips SCN350 Screeneo U4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips SCN350 Screeneo U4 in the language / languages: English as an attachment in your email.

The manual is 8.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips SCN350 Screeneo U4

Philips SCN350 Screeneo U4 User Manual - German - 28 pages

Philips SCN350 Screeneo U4 User Manual - Dutch - 25 pages

Philips SCN350 Screeneo U4 User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info