36844

Philips SBCSC365 Manual

4
Zoom out
Zoom in
Previous page
1/75
Next page
3
IMPORTANT!
This Baby Monitor is intended as an aid. It is not a substitute for responsible and proper adult
supervision and should not be used as such.
Make sure the Baby unit and adapter cable are always out of reach of the baby, at least 1 metre away.
Never place the Baby unit inside the baby’s bed or playpen!
The antennas on the Parent and Baby units are fixed; do not try to extend them.
Never cover the Baby unit (with a towel, blanket, etc.)
CONGRATULATIONS
You have just purchased a high-performance, cordless Baby Monitor that lets you listen to your child
from wherever you are in and around the house. Please read this guide carefully before using the
monitor, and keep it for future reference.
GETTING THE UNITS READY FOR USE
Baby unit
Connect the AC power adapter (A-9) to an AC mains socket, and then connect the cord to the DC
power supply socket (A-6) of the Baby unit.
If you want to use batteries, remove the battery compartment cover (A-8) using a screwdriver. Insert
four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting
the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw.
The Baby unit operates cordlessly for up to 30 hours on fresh batteries. The red POWER light (A-2)
flashes when battery power is low. If this happens install new batteries.
Note: To switch off the Baby unit completely push the POWER button (A-4) .
Parent unit
The Parent unit uses rechargeable batteries. These are already installed, but first they must be charged
for at least 14 hours as follows before using the unit outside the charging base:
• Connect the AC power adapter (B-11) to an AC mains socket, and then connect the cord to the DC
power supply socket (B-10) of the charging base (B-6).
• Place the Parent unit inside the charging base. The red charging light (B-13) lights.
The Parent unit can be operated now but you should leave it in the charging base until the batteries are
fully charged (at least 14 hours). When the batteries are fully charged, take the Parent unit out of the
charging base and use cordlessly for up to 12 hours.
When the red POWER light (B-1) on the Parent unit flashes, the battery power is low. Place the Parent
unit inside the charging base to recharge the batteries.
If the rechargeable batteries begin to lose their effectiveness, replace them with four new batteries
(1.2V, AA NiMH) as follows: remove the battery compartment cover (B-7) using a screwdriver and insert
the batteries noting the + and - configuration inside the battery compartment. Put the cover back in
place and tighten screw. Only use 1.2V, AA NiMH rechargeable batteries!
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips SBCSC365 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips SBCSC365 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info