630697
5
Zoom out
Zoom in
Previous page
1/38
Next page
3. POWER SUPPLY
5
SBC366page 5
Notes
Both the ‘baby unit’ and ‘parent unit’ have a
‘battery low’ indication. If the batteries are
low the unit beeps and the red POWER LED
starts flashing.
To conserve batteries, connect the units to
the mains by using the enclosed mains
adapters.
If batteries are installed and the mains
power adapters are connected, the units
operate on mains power. In the event of a
mains failure, the batteries will take over.
IMPORTANT
Replace batteriesinside the ‘baby unit’ with
original PHILIPS LR6 POWERLIFE batteries
only.
Batteries inside the ‘parent unit’ are already
installed. Replace these batteries with
rechargeable NICAD (R6) batteries ONLY.
DO NOT INSTALL ANY OTHER TYPE OF
BATTERIES INSIDE THE ‘PARENT UNIT’!
English
4. OPERATION
OPERATION
(fig. 4)
‘Baby unit’
Make sure the mains power adapter is
connected correctly, or batteries are
installed.
Place the ‘baby unit’ near the baby’s bed,
making sure that the microphone is placed
in the best position for picking up baby’s
sounds.
IMPORTANT!
Make sure that the ‘baby unit’ is always out of
reach of the baby; never place the ‘baby unit’
inside baby’s bed or playpen!
Select the VOICE mode using the mode
switch
(fig. 1.7)
.
If sound is picked up by the built-in
microphone, the ‘baby unit’ starts
transmitting automatically. The transmission
stops when no sound is picked up any
more. During transmission the green
TRANSMIT LED lights up.
The ‘baby unit’ also has a button for manual
transmission (TALK
fig. 1.8
). This function
operates both during VOICE and OFF-mode.
For manual transmission:
Keep the TALK button pressed and speak
into the microphone.
The green TRANSMIT LED light up.
Spoken sound is transmitted until the TALK
button is released.
‘Parent unit’
Make sure that the mains power adapter is
correctly connected to the recharging base,
or that batteries are installed.
If batteries are installed, the ‘parent unit’
uses rechargeable battery power only in the
event of a mains failure, or when the unit is
not placed inside the standing base.
Place the ‘parent unit’ inside the recharging
base, near to the parent’s location.
If the mains power adapter is connected
correctly, the red CHARGE LED on the
recharging base lights up.
Switch the ‘parent unit’ to ON to an
acceptable sound level
(fig. 1.4)
.
If a sound signal is received from the ‘baby
unit’, it is heard via the built-in speaker.
Adjust the sound level as required.
The ‘parent unit’ checks the received sound
signal. If the quality is too poor, the signal is
blocked.
In this case:
Move the ‘parent unit’ closer to the ‘baby
unit’ to restore sound reception again.
The maximum operating distance is 150 m
in ideal conditions.
Notes
For baby monitoring make sure the ‘baby
unit’ is in VOICE mode!
Do not place ‘baby unit’ and ‘parent unit’ too
close to each other while operating.
Otherwise the units will start resonating
(high-pitch sound).
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips SBC SC366 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips SBC SC366 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info