122355
6
Zoom out
Zoom in
Previous page
1/89
Next page
6
3 Press and hold the key on your original remote control that you
want to copy to the RU460, until the green LED on the RU460 blinks
three times and stays off. Release the key, the function for the
selected key has now been copied.
NOTE:
If you copy a function under a specific key on the RU460, the old
signal will be erased.
If you want to restore the original function of a specific key,
please follow the instructions below:
1 Press and hold and at the same time -for about 3
seconds- until the green LED lights up. (Release the keys, the green
LED should stay on)
2 Press .
3 Press the key that you want to restore. Thats it, the key will
transmit the pre-programmed signal.
If you want to restore all keys in a certain mode, please follow
the instructions below:
1 Press and hold and at the same time -for about 3
seconds- until the green LED lights up. (Release the keys, the green
LED should stay on)
2 Press . Thats it, you have now restored all keys to their original
functions.
ADVANCED TIPS AND TRICKS
The RU460 can be programmed for any combination of devices pre-
programmed in its library. Below you find an example, of course other
combinations are also possible.
To change the AUDIO2 mode to control for instance a second TV
The AUDIO2 mode on this remote is used to control additional
equipment. It is factory preset to control an amplifier, but you can
change it to control a second TV, for example.
Before you start, press to select AUDIO2, and make sure the
second TV is switched on.
1 Press and hold and at the same time - for about 3
seconds - until the green LED lights up. (Release the keys, the green
LED should stay on)
2 Press repeatedly until the second LED appears. Select the
TV mode with the second LED.
3 If you know the brand of your second TV, enter the 3-digit code
using the keypad. The green LED blinks twice.
Thats it! Now, press a few keys on the remote to check that the second
TV responds correctly. If it doesnt or if not all keys are responding
correctly, try again from point 1 using the next code in the list. In the
rare instance that none of the codes work, please follow the instructions
below to start the Handsfree Autosearch:
1 Press and hold and at the same time - for about 3
seconds - until the green LED lights up. (Release the keys, the green
LED should stay on)
2 Press repeatedly until the second LED appears. Select the
TV mode with the second LED.
3 Press to start the search. Each time the green LED blinks,
another code is sent. When the right code is found, the second TV
switches off.
4 Immediately press to stop the search.
If you missed the correct code because the search went too far, switch
the second TV back on, then press to send the previous code again.
Keep pressing down repeatedly until the second TV switches off again.
P
P
3
3
1
1
3
3
1
1
6
6
6
6
1
1
7
7
6
6
1
1
English
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips sbc ru 460 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips sbc ru 460 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info