450370

Philips RQ 1290 Manual

8
Zoom out
Zoom in
Previous page
1/266
Next page
Note: When you place the shaver in the plugged-in charger or Jet Clean System, the travel lock is automatically deactivated.

The appliance is equipped with an automatic power-saving mode. When the shaver enters the power-saving mode, the light in the on/off button
goes out to save energy.
- If you move the appliance for 5 minutes without switching it on, it automatically goes into power-saving mode.
, The lock symbol ashes on the display to indicate that the appliance is in power-saving mode. (Fig. 16)
- To deactivate the power-saving mode, simply press the on/off button.

- If the shaving heads are blocked, the shaving unit symbol, the tap symbol and the exclamation mark ash. In this case, the motor cannot run
because the shaving heads are soiled or damaged. (Fig. 17)
Note: The displays of types RQ1290, RQ1280, RQ1260 and RQ1250 look different, but show the same symbols.
- When this happens, you have to clean the shaving unit or replace it.
- The shaving unit symbol, the tap symbol and the exclamation mark continue to ash until you unblock the shaving heads.

Charging takes approx. 1 hour.
RQ1290/RQ1280/RQ1260: A fully charged shaver has a shaving time of up to 60 minutes/20 days.
RQ1250: A fully charged shaver has a shaving time of up to 50 minutes/16 days.
The actual shaving time is calculated by the shaver. If you have a heavy beard, the shaving time may be less than expected. The shaving time may
also vary over time, depending on your shaving behaviour and beard type.
Charge the shaver before you use it for the rst time and when the display indicates that the battery is almost empty (see section ‘Battery low’
in chapter ‘The display’).

After the shaver has charged for 5 minutes, it contains enough energy for one shave.

1 Put the small plug in the charger (Fig. 18).
2 Put the adapter in the wall socket.
3 Put the shaver in the charger and push it backwards (‘click’). (Fig. 19)
, The display shows that the shaver is charging (see chapter ‘The display’).

1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
3 Place the shaver upside down in the holder with the display pointing towards the front of the Jet Clean System (Fig. 20).
Note: The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit.
Note: RQ1290 only: when you turn the shaver upside down, the minutes indication on the display is also turned upside down so you can still see to
what level the battery is charged.
4 Press the shaver tightly into the holder to lock it into place (Fig. 21).
, The display shows that the shaver is charging (see section ‘Charging’ in chapter ‘The display’).


1 Press the on/off button once to switch on the shaver.
, The display lights up for a few seconds.
2 Move the shaving heads over your skin. Make circular movements (Fig. 22).
- Do not make straight movements.
- Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system.
3 Press the on/off button once to switch off the shaver.
, The display lights up for a few seconds and then shows the remaining battery capacity.

You can also use this shaver on a wet face with shaving foam or shaving gel.
To shave with shaving foam or shaving gel, follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure that the shaving unit glides smoothly over your skin.
4 Press the on/off button once to switch on the shaver.
5 Move the shaving heads in circular movements over your skin.
Note: Rinse the shaver under the tap regularly to ensure that it continues to glide smoothly over your skin.
6 Dry your face and thoroughly clean the shaver after use (see chapter ‘Cleaning and maintenance’).
Note: Make sure you rinse all foam or shaving gel off the shaver.
8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips RQ 1290 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips RQ 1290 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info