492785

Philips REM400 Manual

7
Zoom out
Zoom in
Previous page
1/19
Next page
7
Checking The Auto Scan Codes
If you have set up the remote control using
Auto Scan,you can now find out which four-
digit code is operating your component:
1. On the remote con-
trol, press a compo-
nent key once (e.g.,
TV,VCR,CBL,AUD,DSS,or CD).
2. Press and hold SET until the red
light blinks twice, then release
SET.
3. Enter 9-9-0.The red light will
blink twice.
4. To view the code for the first
digit, press 1 once. Wait 3 sec-
onds, count the red light blinks
(e.g., 3 blinks = 3) and write
down the number.
NOTE: If a code digit is “0”, the
red light will not blink.
5. Repeat step 4 three more times
for remaining digits. Use 2 for
the second digit, 3 for the third
digit, and 4 for the fourth digit.
6. To find codes of other compo-
nents, repeat steps 1 through 5,
but substitute the appropriate
key (e.g., VCR, CBL, AUD, DSS,or
CD) for the component you are
checking. As before, write down
each four-digit code.
Re-Assigning Component Keys
The DSS remote can be set up to control any
combination of six home entertainment
components.By following these instructions,
you can re-assign or duplicate a component
key onto an unused component key.
1. Press and hold SET until the red
light blinks twice, then release
SET.
2. Enter 9-9-2.The red light will
blink twice.
3. Press the Component key (e.g.,
TV, VCR, etc.) to be moved once,
then press the Component key
(e.g.,AUD, etc.) to be re-assigned
once. When re-assignment is
done, the red light will blink
twice to confirm your choice.
4. The re-assigned key is now ready
to be programmed for the new
component. See Programming
Other Components on page 5.
Example – Re-assigning The AUD Key To
Be A DVD (Or VCR) Key:
For example,to have the DSS control a TV,a
Cable Converter, and two VCRs, you will
need to re-assign the unused AUD key to
operate the second VCR as follows:
1. Press and hold SET until the red
light blinks twice, then release
SET.
2. Enter 9-9-2.The red light will
blink twice.
3. Press VCR once.
4. Then press AUD once. When re-
assignment is done,the red light
will blink twice to confirm your
choice.
5. The AUD key is now ready to be
programmed for your DVD (or
VCR) player. See Programming
Other Components on page 5.
PROGRAMMING YOUR REMOTE CONTROL (continued)
REM400 Manual Engl 12/28/99 12:01 PM Page 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips REM400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips REM400 in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info