492790
6
Zoom out
Zoom in
Previous page
1/19
Next page
6
Programming A TV/VCR Combo
Perform the following instructions to have
the I-TV control a TV/VCR Combo. For
Sharp and Sony models,also see page 13.
IMPORTANT: Please completely read and
review these steps before proceeding. Highlight
the code (on page 16) for the brand you wish to
program or write it down in the supplied chart.
Setup Code For My Component
TV/VCR
1. Manually turn on the TV/VCR
Combo; insert a video cassette.
2. On the remote control,press VCR
once.
3. Press and hold SET until the red
light blinks twice, then release
SET.
4. Use the Setup Codes For TV/VCR
Combos (on page 16) to find the
brand name.Enter the first four-
digit code for your component.If
performed correctly, the red
light will blink twice.
5. Aim the remote control at the
TV/VCR Combo. Press POWER
once.It should turn off. If it does
not respond, repeat steps 2-3,
trying each code for your brand
until you find one that works. If
it still doesnt work, use Auto
Scan (later on this page) to pro-
gram your TV/VCR combo.
NOTE: If the TV/VCR Combo
does not have a Power key, press
PLAY
on the I-TV.
6. If youve located a TV/VCR code
that works, but it has a separate
TV code, you’ll also need to pro-
gram it into the remote control to
access volume control as follows:
a. Press TV once.The red
light will blink twice.
b. Press and hold SET
until the red light
blinks twice, then
release SET.
c. Enter the TV code for
the TV/VCR Combo.
If performed cor-
rectly, the red light
will blink twice.
6. (continued)
If there is no separate TV code
listed, you will need to perform
the following steps to access vol-
ume control:
a. Press VCR once.
b. Press and hold SET
until the red light
blinks twice, then
release SET.
c. Press VOL +.
Programming With Auto Scan
If your component does not respond to the
remote control after trying all codes listed for
your brand,or if your brand is not listed at all,
try searching for your code using Auto Scan.
For example,to search for a code for a TV:
1. On the remote control, press TV
once.
2. Press and hold SET until the red
light blinks twice,then release SET.
3. Aim the remote control at the TV
and press SCAN.The red light will
blink twice.
4. Continue aiming the remote con-
trol at the TV (which may take up
to 5 minutes) until it turns off.
Immediately press any key except
VOL+, VOL–, EXIT, SCAN,or SET.
NOTES: In the search mode, the
remote will send IR (infrared)
codes from its library to the
selected device, starting with the
most popular code first.
If you have passed by the code
that turns off the TV, press
VOL–
one or more times until the TV
turns on again.
5. To lock in the code and exit Auto
Scan, press and release SET the
red light will blink twice.
6. To search for codes of other com-
ponents, repeat steps 1 through
5, but substitute the appropriate
key (e.g., VCR, CBL, AUD, DSS,or
CD) for the (VCR, Cable, Audio,
Satellite, or CD) component you
are searching for.
PROGRAMMING YOUR REMOTE CONTROL (continued)
REM380 Manual Engl 12/28/99 12:10 PM Page 6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips REM380 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips REM380 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info