537653
6
Zoom out
Zoom in
Previous page
1/69
Next page
Trimming with precision trimming head and precision
trimming comb
1 Put the precision trimming head on the appliance (see section
‘Attaching and detaching the attachments’ in chapter ‘Preparing for
use’).
2 Choose the short, medium or long precision trimming comb,
depending on the desired hair length. The indications ‘S’, ‘M’ and ‘L
are on the combs.
Short precision trimming comb (S): 4mm
Medium precision trimming comb (M): 5mm
Long precision trimming comb (L): 6mm
Tip: We advise you to start trimming with the long comb.
3 Put the precision trimming comb on the precision trimming head and
push it until it locks into place (‘click’).
4 Switch on the appliance. Turn the battery compartment cover from
the ‘off’ position (0) to the ‘on’ position (I).
5 Move the appliance slowly and with light pressure against the
direction of hair growth.
Note: To make trimming easier, stretch the skin with your free hand during
trimming.
Note: Make sure that the at part of the comb always touches the skin to
obtain an even result.
Note: Do not press the appliance with the comb onto the skin too hard. This
may cause the appliance to trim the hairs shorter than the length indicated on
the comb.
Note: In areas where the hair grows in different directions, move the appliance
upwards, downwards and sideways.
6 Regularly remove cut hairs from the comb. If a lot of hairs have
accumulated in the comb, detach the comb from the appliance and
blow and/or shake the hairs out of it.
-
-
-
ENGLISH10
7 To switch off the appliance, turn the battery compartment to the ‘off
indication (0).
8 Todetachthecomb,putyourngerunderthebottomedgeofthe
comb and pull it off the appliance.
Shaving with precision shaving head
1 Put the precision shaving head on the appliance (see section
‘Attaching and detaching the attachments’ in chapter ‘Preparing for
use’).
2 Place the precision shaving head at a 45° angle onto the skin and
move the appliance slowly and smoothly against the direction of hair
growth.
3 Make sure that the whole shaving head is in contact with the skin.
As hairs grow in different directions move the appliance in different
directions against the hair growth.
4 To switch off the appliance, turn the battery compartment to the ‘off
indication (0).
Cleaning
Clean the appliance immediately after use and when a lot of hair or dirt
has accumulated on the cutting elements.
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
Do not tap on the cutting elements.
Do not use any sharp objects to clean the cutting elements.
1 Switch off the appliance.
ENGLISH 11
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips NT9145 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips NT9145 in the language / languages: All languages as an attachment in your email.

The manual is 25,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info