215271
10
Zoom out
Zoom in
Previous page
1/34
Next page
3. Set up >
Place the projector on a stable, level surface, out of direct sunlight and away from sources of
excessive dust, dirt, heat, water, moisture, vibration and strong magnetic fields.
Allow sufficient cooling of the product by keeping all air inlets and outlets clear from
obstructions.
Position the projector in such way that the viewers cannot watch into the projector light beam.
Choose a screen size suitable for the number of viewers and the size of the room.
Picture quality is best when you sit directly in front of the projector screen.
The projector can be used for both front projection, rear projection and ceiling projection
applications. As default factory setting, the projector has been set up for front projection.You
can change to rear or ceiling projection via the Mirror function in the Picture menu.
1 Insert the mains lead into the projectors Mains inlet socket and connect it to the wall socket.
The Standby indicator lights up red, the projector is now in the Power/Standby mode.
2 Remove the lens cap.
3 Press any button on projector or remote control to switch on the projector.
The Standby indicator lights up orange.
When the projection lamp is on, the Standby indicator lights up green and the start-up
screen appears for several seconds.
4 Press the Standby button to switch the projector back into the Power/Standby mode.
The Standby Warning screen will appear for 20 seconds.
The Standby Warning screen can be removed by pressing the OK button.
5 Press the Standby button again to confirm.
The projector will now go into Power/Standby mode.
You can also press the Standby button twice in succession to switch the projector into Power/Standby
mode immediately.
6 To switch off the mains supply completely, disconnect the mains lead.
Save energy! Please put the projector in the Power/Standby position if you are not going to use the
projector for more than 15 minutes.
When no signal inputs are detected for 30 minutes, the projector automatically switches
to Power/ Standby (Auto Standby).This setting can be changed in the ‘Settings’ menu
Before disconnecting the mains lead, make sure that the cooling fan has stopped
(about 3 minutes after the projector has been switched to Power/Standby).
Positioning the projector
and screen
Switching on the projector
Notes
Philips Multimedia Projector 10 English User guide bSure1 / bSure 2
SCREEN
SCREEN
SCREEN
SCREEN
Front projection Ceiling front projection
Rear projection Ceiling rear projection
Menu OK
AV
Mute
Source
Stand
by
Lamp
Temp
Menu OK
AV
Mute
Source
Stand
by
Lamp
Temp
Warning

If the projector is switched off you have to 
wait 1 minute before switching on the 
projector again to allow adequate time 
for the lamp to cool down.
Press stand-by key again to confirm.
Press OK key to remove this warning.
PHILIPS
PHILIPS
PHILIPS
Multimedia Projectors
Multimedia Projectors
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips lc3142 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips lc3142 40 in the language / languages: English as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info