330
27
Zoom out
Zoom in
Previous page
1/30
Next page
9. ADDITIONAL INFORMATION Connecting RS-232C port/Maintenance
CONNECTING RS-232C PORT
When the RS-232C port on the projector is connected to a
computer with an RS-232C cable (cross type, sold separately),
the computer can be used to control the projector and check
the status of the projector.
1. Connect the supplied DIN-D-sub RS-232C cable to the
RS-232C port on the projector.
2. Connect a RS-232C cable (sold separately) to the other end
of DIN-D-sub RS-232C cable and to the serial port on the
computer. See page 13 for details.
CAUTION!
Do not connect or remove RS-232C cable to or from the
computer while it is on. This may damage your computer.
The wireless mouse or RS-232C function may not operate if
your computer port is not correctly set up. Please refer to
the operation manual of the computer for details on setting
up/installing the correct mouse driver.
A Macintosh adapter may be required for use with some
Macintosh computers. Contact your nearest Philips
Authorised LCD Projector Dealer or Service Centre.
For more details on specification of the use of the RS-232C
please contact your nearest Philips Authorised LCD projector
Dealer or Service Centre.
AIR FILTER MAINTENANCE
This projector is equipped with two air filters to ensure the
optimal operating condition of the projector.
The air filters should be cleaned every 100 hours of use.
Clean the filters more often when the projector is used in a
dusty or smoky location.
Have your nearest Philips Authorised LCD Projector Dealer
or Service Centre exchange the filter when it is no longer
possible to clean it.
Cleaning and replacing the bottom air filter
1. Unplug the power cord.
2. Remove the bottom filter cover.
Turn over the projector. Press the tab and lift open the filter
cover in the direction of the arrow.
3. Remove the air filter.
Grasp the air filter between your fingers and lift it out of the
filter cover.
4. Clean the air filter. Clean the dust off the air filter and cover
with a vacuum cleaner extension hose.
5. Replace the air filter. Place the air filter underneath the tabs
on the filter frame.
6. Replace the filter cover. Insert the tab on the end of the
filter cover into the filter cover opening and press the filter
cover into position.
Note:
Be sure the filter cover is securely installed. The power will not
turn on unless it is correctly installed.
Cleaning the side air filter (not removable)
If dust or dirt has collected inside the air filter, clean the filter
with a vacuum cleaner extension hose.
Note:
The side air filter cannot be removed.
LAMP MAINTENANCE
Lamp/Maintenance Indicators
The warning lights on the projector indicate problems inside
the projector.
There are two warning lights: a temperature warning
indicator (Temp.) which warns that the projector is too hot,
and a Lamp indicator (Lamp) which lets you know when to
change the lamp.
If a problem occurs, either the Temperature warning
indicator or the Lamp indicator will light up red. After turning
off the power, follow the procedures given in the next table.
))
25
English
Air
filter
Air filter
(not removable)
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips lc1041 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips lc1041 in the language / languages: English, Dutch as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info