696521

Philips HI 5916 Manual

6
Zoom out
Zoom in
Previous page
1/46
Next page
8
English
2 Place the Calc-Clean container on the ironing board or any other even, stable surface.
3 Place the iron stably on the Calc-Clean container (Fig. 5).
Note: The Calc-Clean container has been designed to collect scale particles and hot water during
the Calc-Clean process. It is perfectly safe to rest the iron on this container during the entire
process.
4 Press and hold the Calc-Clean button for 2 seconds until you hear short beeps (Fig. 6).
5 During the Calc-Clean process, you hear short beeps and a pumping sound (Fig. 7).
6 When the Calc-Clean process is completed, the iron stops beeping and the CALC-CLEAN light
stops ashing (Fig. 8).
7 Wipe the iron with a piece of cloth and put it back on the base station (Fig. 9).
8 As the Calc-Clean container becomes hot during the Calc-Clean process, wait approx. 5 minutes
before you touch it. Then carry the Calc-Clean container to the sink, empty it and store it for future
use (Fig. 10).
9 If necessary, you can repeat steps 1 to 7. Make sure that you empty the Calc-Clean container before
you start the Calc-Clean process.
Note: During the Calc-Clean process, clean water may come out of the soleplate if no scale has
accumulated inside the iron. This is normal.
Troubleshooting
This chapter summarizes the most common problems you could encounter with the appliance. If you
are unable to solve the problem with the information below, visit www.philips.com/support for a list
of frequently asked questions or contact the Consumer Care Center in your country.
Problem Possible cause Solution
The iron does not
produce any steam.
You have set the
temperature dial to SYNTH
to 1.
Turn the temperature dial to 2 or higher.
The steam function has
been disabled until you
have performed the Calc-
Clean process.
Perform the Calc-Clean process to restore
the steam function (see chapter ‘Cleaning
and maintenance’).
At the start of your ironing
session, the steam trigger
has not been pressed long
enough.
Press and hold the steam trigger until
steam comes out. It may take up to 30
seconds until steam comes out.
The Calc-Clean light
ashes. No steam comes
out of the soleplate and/
or the appliance beeps.
You have not done or have
not completed the Calc-
Clean process.
Perform the Calc-Clean process to enable
the steam function again (see chapter
‘Cleaning and maintenance’).
The appliance has
switched o.
The auto shut-o function
is activated automatically
when the appliance has not
been used for more than 5
minutes.
To activate the appliance again, set the on/
o switch to ‘o’ position and then to ‘on’
position. The appliance then starts to heat
up again.
The appliance produces
a loud pumping sound.
The water tank is empty. Fill the water tank with water and press
the steam trigger until the pumping sound
becomes softer and steam comes out of
the soleplate.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips HI 5916 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips HI 5916 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info