674141
18
Zoom out
Zoom in
Previous page
1/36
Next page
18
EN
9 Troubleshooting
If you encounter problems when using this multicooker, check the following points before requesting
service. If you cannot solve the problem, contact the Philips Consumer Care Center in your country.
Problem Solution
SD” appears on the display
when the multicooker is in
standby mode.
SD” is short for “standby” and means that the multicooker is in
standby mode.
The light on the button does
not go on.
There is a connection problem. Check if the power cord is connected
to the multicooker properly and if the plug is inserted rmly into the
power outlet.
The light is defective. Take the appliance to your Philips dealer or a
service center authorized by Philips.
The display does not
function.
The multicooker is not connected to the power supply. If there is no
power supply, the power failure backup function does not work and
the display does not function.
The battery for the display runs out of power. Take the appliance to
your Philips dealer or a service center authorized by Philips to have the
battery replaced.
The rice is not cooked. There is not enough water. Add water according to the scale on the
inside of the inner pot.
You did not press the start button (On/Off).
Make sure that there is no foreign residue on the heating element and
the outside of the inner pot before switching the multicooker on.
The heating element is damaged, or the inner pot is deformed. Take
the multicooker to your Philips dealer or a service center authorized by
Philips.
The rice is too dry and not
well cooked.
Add more water to the rice, and cook for a bit longer.
The multicooker does not
switch to the keep-warm
mode automatically.
You might have pressed the keep-warm button (Chaud) before
pressing the start button (On/Off). In this case the multicooker will be
in standby mode after the cooking is nished.
The temperature control is defective. Take the appliance to your Philips
dealer or a service center authorized by Philips.
The rice is scorched. You have not rinse the rice properly. Rinse the rice until the water runs
clear.
Water spills out of the
multicooker during cooking.
Make sure that you add water to the level indicated on the scale inside
the inner pot that corresponds to the number of cups of rice used.
I cannot get to the desired
cooking function.
Press the menu button (Menu) repeatedly to select the desired
function as shown by the indicator.
Rice smells bad after cooking Clean the inner pot with some washing detergent and warm water.
After cooking, make sure the steam vent cap, inner lid and inner pot is
cleaned thoroughly.
Error message (E1, E2, E3, or
E4) appears on the display.
There has been a power failure during cooking. Take the appliance to
your Philips dealer or a service center authorized by Philips.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips HD3167 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips HD3167 in the language / languages: English, French as an attachment in your email.

The manual is 5,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info