578102

Philips GC9237 Manual

11
Zoom out
Zoom in
Previous page
1/42
Next page
Problem Possible cause Solution
The ironing board
cover becomes
wet.
Steam has condensed on the
ironing board cover after a
long ironing session.
Replace the ironing board cover if the foam
material has worn out. You can also add an extra
layer of felt material under the ironing board cover
to prevent condensation on the ironing board.
Water droplets
come out of the
soleplate.
The steam that was still present
in the hose has cooled down
and condensed into water.
Point the iron away from the garment and let it
produce steam for a few seconds.
Steam and/or
water comes out
from under the
EASY DE-CALC
knob.
The EASY DE-CALC knob is
not tightened properly.
Switch off the appliance and wait for two hours
for steam generator to cool down. Unscrew the
EASY DE-CALC knob reattach it properly. Note:
When you remove the knob, water comes out
of the steam generator. If steam continues to
escape, switch off the appliance and contact an
authorised Philips service centre.
Dirty water
and impurities
come out of the
soleplate.
Impurities or chemicals
present in the water have
deposited in the steam vents
and/or on the soleplate.
Descale the steam generator regularly. See
section ‘Cleaning the soleplate’ in chapter
‘Cleaning and maintenance’.
Too much scale and minerals
have accumulated inside the
steam generator.
Descale the steam generator regularly.
See section ‘IMPORTANT - Descaling the steam
generator’ in chapter ‘Cleaning and maintenance’.
The iron leaves a
shine or an imprint
on the garment.
The surface to be ironed was
uneven, for instance because
you were ironing over a seam
or a fold in the garment.
Perfect Care is safe on all garments. The shine or
imprint is not permanent and will come off if you
wash the garment. Avoid ironing over seams or
folds or you can place a cotton cloth over the
area to be ironed to avoid imprints.
The steam
generator does
not produce any
steam.
There is not enough water in
the water tank (the ‘water tank
empty’ light ashes).
Fill the water tank and press the steam trigger
to let the appliance heat up again. When the
‘iron ready’ light lights up continuously, you can
continue steam ironing.
The steam generator is not
hot enough to produce steam.
Wait until the ‘iron ready’ light on the iron lights
up continuously.
You did not press the steam
trigger.
Press the steam trigger and keep it pressed while
you iron.
The water tank is not placed
properly in the steam generator.
Slide the water tank rmly back into the steam
generator (‘click’).
The steam
generator
produces a
pumping sound.
Water is pumped into the
boiler inside the steam
generator. This is normal.
If the pumping sound continues nonstop, switch
off the steam generator and remove the plug
from the wall socket. Contact an authorised
Philips service centre.
The steam
generator
produces a loud
pumping sound
intermittently.
There is not enough water in
the water tank (the ‘water tank
empty’ light ashes).
Fill the water tank and press the steam trigger
to let the appliance heat up again. When the
‘iron ready’ light lights up continuously, you can
continue steam ironing.
ENGLISH 11
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips GC9237 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips GC9237 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info