583579

Philips GC6632 Manual

8
Zoom out
Zoom in
Previous page
1/36
Next page
Safety auto-off mode (specic types only)
- To save energy, the steam generator switches off automatically when it has not been used for
15 minutes. The ‘iron ready’ light ashes.
- To reactivate the steam generator, set the on/off switch to ‘off’ position and then to ‘on’ position.
Troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If
you are unable to solve the problem with the information below, visit www.philips.com/support
for a list of frequently asked questions or contact the Consumer Care Centre in your country.
Problem Possible cause Solution
The iron does
not produce any
steam.
There is not enough water in
the water tank.
Fill the water tank beyond the MIN
indication. Press and hold the steam trigger
until steam comes out. It may take up to
30 seconds until steam comes out.
You have not pressed the steam
trigger.
Press and hold the steam trigger until
steam comes out.
You have set the temperature
dial to 1.
Turn the temperature dial to 2 or higher.
The steam function has been
disabled until you have
performed the Calc-Clean
process.
Perform the Calc-Clean process to restore
the steam function
(see chapter ‘IMPORTANT - Cleaning and
maintenance’).
The Calc-Clean
light ashes and 
the appliance
beeps.
This is the Calc-Clean reminder. Perform the Calc-Clean process within
1 hour after the Calc-Clean reminder is
given.
The Calc-Clean
light ashes and/
or the appliance
beeps.
You have not done or have not
completed the Calc-Clean
process.
Perform the Calc-Clean process to enable
the steam function again
(see chapter ‘IMPORTANT - Cleaning and
maintenance’).
The Calc-Clean
light ashes and 
the appliance
beeps every time
I press the steam
trigger. No steam
comes out of the
soleplate.
You have not done or have not
completed the Calc-Clean
process.
Perform the Calc-Clean process to enable
the steam function again
(see chapter ‘IMPORTANT - Cleaning and
maintenance’).
The appliance has
switched off.
The safety auto-off function was
activated. This happens
automatically when the steam
generator has not been used or
the steam trigger has not been
pressed for more than 15
minutes.
Set the on/off switch to ‘off ’ position and
then to ‘on’ position.
ENGLISH8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips GC6632 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips GC6632 in the language / languages: English, German, Dutch, French, Italian, Swedish, Finnish as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info