101360

Philips GC4030 Azur Manual

11
Zoom out
Zoom in
Previous page
1/68
Next page
11
Trouble shooting guide
This chapter summarizes the most common problems you could
encounter with your iron. Please read the different sections for more
details. If you are unable to solve the problem, please contact the
nearest Philips Service Centre or one of its representatives. See the
worldwide guarantee leaflet for telephone numbers of the Philips
Helpdesk or visit our website at www.philipsonline.com.
ENGLISH
Solution
Check the mains cord, the plug and
the wall socket.
Fill the water tank (see Filling the
water tank).
Set to steam position between 1-6
(see Steam ironing).
Set the temperature control to the
steam area (2 to MAX). Put the
iron on its heel and wait until the
amber pilot light has gone out before
you start ironing.
Put the iron in horizontal position and
wait for a while before using the
(Vertical) Shot of Steam function
again.
Set the temperature control to the
steam area (2 to MAX). Put the
iron on its heel and wait until the
amber pilot light has gone out before
you start ironing.
Press to close the filling cap tightly
until you hear a click.
Apply Calc-Clean a few times (see
Calc-Clean).
Shake the iron slightly to deactivate
the Auto-shut-off, the lamp will stop
blinking.
Possible cause(s)
Connection problem.
Not enough water in the water tank.
The steam control has been set to
position O.
The iron is not hot enough and/or
Drip Stop is activated.
The (Vertical) Shot of Steam function
has been used too often within a very
short period.
The iron is not hot enough and/or
Drip Stop is activated.
The filling cap is not closed properly.
Hard water form flakes inside the
soleplate.
Auto-shut-off is activated. See "Auto-
shut-off" section.
Problem
The iron is plugged in but the
soleplate is cold.
No steam
No Shot of Steam or No Vertical
Shot of Steam (Type GC4043,
GC4040, GC4038, GC4035, GC4033,
GC4030, GC4028, GC4025, GC4023,
GC4020, GC4018, GC4015, GC4013,
GC4010)
Water droplets on fabric
Flakes and impurities coming out
from soleplate during ironing.
Red pilot light blinks (Type GC4043,
GC4040, GC4038, GC4035, GC4033,
GC4030).
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips GC4030 Azur at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips GC4030 Azur in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info