323681
12
Zoom out
Zoom in
Previous page
1/114
Next page
Problem Possible cause Solution
The set ironing temperature is too low. Set a higher ironing temperature.
Some smoke
comes out of the
appliance after I
have switched it on
for the rst time.
This is normal. Some parts of the
appliance have been greased lightly in the
factory.
This phenomenon ceases after a
short while.
The appliance
produces a
pumping sound.
Water is pumped into the boiler inside
the steam generator.This is normal
If the pumping sound continues
non-stop, switch off the appliance
immediately and unplug it. Contact
an authorised Philips service centre.
The appliance does
not produce any
steam.
There is not enough water in the water
tank.
Fill the water tank.
The steam generator is not hot enough to
produce steam.
Wait until the steam setting light
stays on.
You are not pressing the steam trigger. Press the steam trigger and keep it
pressed while you steam iron.
The water tank is not placed properly in
the appliance.
Slide the water tank rmly back into
the steam generator (‘click’).
Superheated (i.e. high-quality) steam
is hardly visible, especially when the
temperature dial is set to maximum
position and even less so when the
ambient temperature is relatively high.
To check if the iron really produces
steam, set the iron to a lower
temperature setting between
2 and 3 for more visible steam.
The appliance is not switched on. Set the power knob with steam
control to a steam setting.
Water droplets
come out of the
soleplate.
When you start steam ironing and
when you continue steam ironing after
an interruption, the steam that was still
present in the hose has cooled down and
condensed into water. This causes water
droplets to come out of the soleplate.
This is normal. Hold the iron over an
old cloth and press the steam trigger.
The cloth absorbs the drops. After a
few seconds, steam instead of water
comes out of the soleplate.
The temperature dial is set to a
temperature that is too low for steam
ironing.
Set an ironing temperature that
is suitable for steam ironing
(temperature settings 2 to MAX).
Wet spots appear
on the garment
during ironing.
The wet spots that appear on your
garment after you have steam ironed for
some time may be caused by steam that
has condensed onto the ironing board.
Iron the wet spots without steam
for some time to dry them. If the
underside of the ironing board is wet,
wipe it dry with a piece of dry cloth.
Water leaks from
the appliance.
If you tilt the steam generator during
transport or place it on an uneven surface
when the water tank is full, water may spill
out of the water tank.
Do not tilt the appliance when the
water tank is full.
ENGLISH12
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips gc 8460 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips gc 8460 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info