1061

Philips DVDR600 Manual

11
Zoom out
Zoom in
Previous page
1/88
Next page
Hookups (cont’d) 11
Connecting to a TV and a Cable Box or Satellite Receiver
1
Connect your Satellite or Cable TV signal to the ANTENNA IN jack
on your Cable Box/Satellite Receiver.
2
If your Cable Box/Satellite Receiver has a single ANTENNA OUT or
TO TV jack: Connect the supplied RF coaxial cable to the
ANTENNA OUT/TO TV jack of the Cable Box/Satellite Receiver
and to the ANTENNA IN jack on the rear of the Recorder.
If your Cable Box/Satellite Receiver has AUDIO/VIDEO OUT jacks: Connect them to
the Recorder’s EXT 2 VIDEO IN and AUDIO IN jacks.These jacks are red and white
(AUDIO) and yellow (VIDEO). Use the supplied audio and video cables, which have
red/white/yellow markings.
3
Connect another RF coaxial cable to the Recorder’s ANTENNA
OUT jack and to the ANTENNA IN or RF IN jack on your TV. Your
TV’s Antenna In jack may be labelled RF In or 75 ohm. Check your TV manual
for details. Or, use an Audio/Video connection between the Recorder and the
TV. See pages 12-15.
4
Connect the power cords of the Recorder, Cable Box/Satellite
Receiver, and TV to a power outlet.
5
Press STANDBY/ON
yy
to turn on the Recorder. Set the Recorder
to channel 3 or 4 (your Cable Box/Satellite Receiver’s output
channel) if you used an RF coaxial cable to connect the Cable
Box/Satellite Receiver to the Recorder.
Set the Recorder to EXT 2 if you used those jacks on the Recorder
to connect to the Cable Box/Satellite Receiver.
6
Tu rn on the TV and the Cable Box/Satellite Receiver.
Set the TV to channel 3 to receive the picture from the Recorder (if
you used the RF coaxial cable as shown for step 3).
You should see the DVD background picture or the Initial Setup screen on the
TV. The Initial Setup screen will appear the first time you turn on the Recorder. Go to
page 18 to continue.
•To watch TV, put the
Recorder in Monitor mode
and on channel 3 or 4. (Press
MONITOR on the
Recorder’s remote.) Change
TV channels at your Cable
Box or Satellite Receiver.
• If “IS TV ON? C03” appears on
the display panel, you need to
turn on your TV and set it to
channel 3.You cannot see the
Initial Setup screens until you
turn on the TV and have it on
the correct Video In channel.
• If channel 3 is already occupied,
you may need to use channel 4
as your Recorder's output
channel instead.To change the
output channel to channel 4,
press STANDBY-ON y to turn
off the Recorder. Press DVD on
the remote.Then press and hold
the Number 4 button on the
remote for several seconds until
you see "C04" on the display
panel. Now the Recorder's output
channel is set to channel 4. Set
your TV to channel 4.The Initial
Setup screen should appear.
Helpful Hints
E9480UD_EN.qx3 05.1.8 4:15 PM Page 11
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips DVDR600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips DVDR600 in the language / languages: Dutch as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info