Manual Philips-Avent SCD497 (page 8 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

507148

Zoom out

Zoom in

1/124

Make sure the + and – poles of the batteries point in the right direction.

3 Slide the battery compartment lid back onto the back of the parent unit until it locks into

position (‘click’) (Fig. 8).

4 Put the small appliance plug in the parent unit and put the adapter in a wall socket (Fig. 9).

5 Leave the parent unit connected to the mains until the batteries are fully charged.



parent unit and let it charge continuously for at least 10 hours.

Charging normally takes 8 hours, but it takes longer when the parent unit is switched on

while charging. To keep the charging time as short as possible, switch off the parent unit

during charging.

The battery check light goes out when the batteries are fully charged.

When the batteries are fully charged, the parent unit can be used cordlessly for at least

24 hours.

Note: The operating time of 24 hours is based on the assumption that the baby unit transmits 25% of

the time and is in standby mode for the rest of the time (when the baby does not make any sound).

Note: When the parent unit batteries are charged for the rst time, the operating time is less than 24

hours. The batteries only reach their full capacity after you have charged and discharged them four times.

Note: When the batteries are running low, the battery check light ashes red. Put the small appliance

plug in the parent unit and put the adapter in a wall socket to recharge the batteries.

Note:When the parent unit is not connected to the mains, the batteries gradually discharge, even when

the parent unit is switched off.

Mains operation

1 Put the small appliance plug in the parent unit and put the adapter in a wall socket (Fig. 9).

Using the appliance

Place the parent unit and the baby unit in the same room to test the connection (Fig. 10).

Make sure the baby unit is at least 1 metre/3 feet away from the parent unit.

2 Press and hold the on/off button 3 on the baby unit for 2 seconds. (Fig. 11)

The nightlight lights up briey.

The ON light lights up.

3 Press and hold the on/off button 3 on the parent unit for 2 seconds. (Fig. 12)

The sound level lights light up blue briey.

The battery check light lights up briey.

The LINK light lights up red briey and then starts to ash green while the parent unit tries

to establish connection with the baby unit.

The LINK light on the parent unit ashes green until connection has been established.

This takes up to 30 seconds. The LINK light on the parent unit then lights up

green continuously.

If no link is established after 30 seconds, the LINK light on the parent unit ashes red and the

parent unit beeps from time to time.

4 Place the baby unit at least 1 metre/3 feet away from your baby (Fig. 13).

5 Position the parent unit within the operating range of the baby unit. Make sure it is at least 1

metre/3 feet away from the baby unit (Fig. 14).

For more information on the operating range, see section ‘Operating range’ below.

ENGLISH8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Philips-Avent SCD497 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Philips-Avent SCD497 Manual

Product: