676099
19
Zoom out
Zoom in
Previous page
1/65
Next page
Fine tune
To fine tune a channel, select Fine tune and
press OK. You can fine tune the channel
with or .
If you want to store the channel found,
select Done and press OK.
Store
You can store the channel on the current channel
number or as a new channel number.
Select Store and press OK. The new channel
number is shown briefly.
You can redo these steps until you have found all
available analogue TV channels.
Satellite
Search for Satellite and Satellite Settings
Search for Satellite Channel
(Home) > Settings > Install
Channels > Satellite installlation > Search for
satellite
Update existing channel list
(Home) > Settings > Install
Channels > Satellite installlation > Search for
satellite > Update channels
Re-install all channels
(Home) > Settings > Install
Channels > Satellite installlation > Search for
satellite > Reinstall channels
• Select the group of channels you want to install.
• Satellite operators can offer channel packages that
bundle free channels (free-to-air) and offer a sorting
that suits a country. Some satellites offer subscription
packages - a collection of channels you pay for.
Satellite Settings
(Home) > Settings > Install
Channels > Satellite installlation > Search for
satellite > Reinstall channels
1 - Select From a sorted package or All channels
unsorted.
2 - Select Settings and press OK.
3 - Press Reset to reset, or
press Done when complete the settings.
Connection type
Select the number of satellites you want to install.
The TV sets the appropriate connection type
automatically.
Up to 4 Satellites - You can install up to 4 satellites
(4 LNBs) on this TV. Select the exact number of
satellites you wish to install at the start of the
installation. This will speed up the installation.
Unicable - You can use a Unicable system to
connect the antenna dish to the TV. You can select
Unicable for 1 or for 2 satellites at the start of the
installation.
LNB settings
In some countries, you can adjust the expert settings
for homing transponder and each LNB. Only use or
change these settings when a normal installation fails.
If you have non-standard satellite equipment, you
can use these settings to overrule the standard
settings. Some providers might give you some
transponder or LNB valeus which you can enter here.
• LNB Power - By default, LNB Power is set to On.
• 22 kHz Tone - By default, the Tone is set to Auto.
• Low LO Frequency / High LO Frequency - The local
oscillator frequencies are set to standard values.
Adjust the values only in case of exceptional
equipment that needs different values.
Add Satellite or Remove Satellite
(Home) > Settings > Install
Channels > Satellite installlation > Search for
satellite > Add satellite, Remove satellite
(Home) > Settings > Install
Channels > Satellite installlation > Search for
satellite > Add satellite
• You can add an additional satellite to your current
satellite installation. The installed satellites and their
channels remain untouched. Some satellite operators
do not allow adding a satellite.
• The additional satellite should be seen as an extra, it
is not your main satellite subscription or not the main
satellite of which you use its channel package.
Typically, you would add a 4th satellite when you
have 3 satellites already installed. If you have 4
satellites installed, you might consider removing one
first to be able to add a new satellite.
• If you currently have only 1 or 2 satellites installed,
the current installation settings might not allow
adding an extra satellite. If you need to change the
installation settings, you must redo the complete
satellite installation. You cannot use Add satellite if
a change of settings is needed.
(Home) > Settings > Install
19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips 50PUS6203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips 50PUS6203 in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips 50PUS6203

Philips 50PUS6203 Additional guide - English - 9 pages

Philips 50PUS6203 User Manual - German - 73 pages

Philips 50PUS6203 Additional guide - German, Dutch - 9 pages

Philips 50PUS6203 User Manual - Dutch - 70 pages

Philips 50PUS6203 Additional guide - French, Italian, Turkish, Spanish - 9 pages

Philips 50PUS6203 Quick start guide - All languages - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info