578538
49
Zoom out
Zoom in
Previous page
1/55
Next page
47
1
0. Troubleshooting & FAQ
s
10. Troubleshooting & FAQs
10.1 Troubleshooting
This page deals with problems that can be
corrected by a user. If the problem still persists
after you have tried these solutions, contact
Philips customer service representative.
Common Problems
No Picture (Power LED not lit)
 Make sure the power cord is plugged into
the power outlet and into the back of the
monitor.
 First, ensure that the power button on the
front of the monitor is in the OFF position,
then press it to the ON position.
No Picture (Power LED is White)
 Make sure the computer is turned on.
 Make sure the signal cable is properly
connected to your computer.
 Make sure the monitor cable has no bent
pins on the connect side. If yes, repair or
replace the cable.
 The Energy Saving feature may be activated
Screen says
Attention
Check cable connection
 Make sure the monitor cable is properly
connected to your computer. (Also refer to
the Quick Start Guide).
 Check to see if the monitor cable has bent
pins.
 Make sure the computer is turned on.
AUTO button doesn't function
 The auto function is applicable only in
VGA-Analog mode. If the result is not
satisfactory, you can do manual adjustments
via the OSD menu.
Note
The Auto Function is not applicable in DVI-
Digital mode as it is not necessary.
Visible signs of smoNe or sparNs
 Do not perform any troubleshooting steps
 Disconnect the monitor from mains power
source immediately for safety
 Contact with Philips customer service
representative immediately.
Imaging Problems
Image is not centered
 Adjust the image position using the “Auto”
function in OSD Main Controls.
 Adjust the image position using the Phase/
Clock of Setup in OSD Main Controls. It is
valid only in VGA mode.
Image vibrates on the screen
 Check that the signal cable is properly
securely connected to the graphics board
or PC.
Ver tical ÁicNer appears
 Adjust the image using the “Auto” function
in OSD Main Controls.
 Eliminate the vertical bars using the Phase/
Clock of Setup in OSD Main Controls. It is
valid only in VGA mode.
Horizontal ÁicNer appears
 Adjust the image using the “Auto” function
in OSD Main Controls.
 Eliminate the vertical bars using the Phase/
Clock of Setup in OSD Main Controls. It is
valid only in VGA mode.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips 272S4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips 272S4 in the language / languages: English as an attachment in your email.

The manual is 3,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips 272S4

Philips 272S4 User Manual - German - 55 pages

Philips 272S4 User Manual - Dutch - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info