33127
26
Zoom out
Zoom in
Previous page
1/28
Next page
If you encounter problems with your TV-Video Combi, these
could be caused by one of the following. You can also call the
customer service centre in your country.
The telephone number is listed in the enclosed warranty
information packet or on the last page of the manual cover.
Have the model number (MODEL NO) and the production
number (PROD.NO) of your video recorder ready. You can find
both numbers printed on the type plate fixed at the rear of the
set.
Your TV-Video Combi does not respond to any button being
pressed:
TV-Video Combi has been switched off using the power switch
8 : switch machine on on left side using the power switch.
There is no power supply: Check the power supply.
A programmed recording is currently being made: If desired,
cancel the programmed recording pressing the
STANDBY m
button (for longer than 3 seconds).
Parental control is on: Switch the parental control off.
Remote control does not work
The red standby lamp (STANDBY 5) does not blink, if one of the
buttons on the remote control is pressed:
Remote control not pointed toward the TV-Video Combi: Point the
remote control at the TV-Video Combi.
There is a technical problem: Take out the batteries, wait for 10
seconds and place them back.
Batteries are weak: Change the batteries.
Technical problem:
Switch machine off using power switch 8 , wait 30 seconds
and switch back on.
You can reset the settings on your set (careful: all information will
be deleted):
1. Switch machine off using power switch
8 .
2. Press the
m button on the machine and hold button. Switch
back on using power switch
8 .
3. If the standby lamp (
STANDBY 5) on the set begins to blink,
release the
m button.
The machine settings are reset and the data memory is deleted.
No picture (black/blue picture):
The red standby lamp (STANDBY 5) on the front of the set is not
lit up:
TV-Video Combi switched off: Switch on the set using the mains
switch on the left side of the unit.
There is no power supply: Check the power supply.
The red standby lamp (
STANDBY 5) on the front of the set is lit:
TV-Video Combi switched off automatically: Switch it back on
using the
;P q button.
Switched to the programme number of an external source, e.g.:
E1’ for the scart socket EXT , but the attached device is
turned off: Switch on external device or choose a different
programme number.
A TV channel (programme number) has been chosen but there is
no reception on this channel: Select the correct TV channel.
No reception: Have the aerial checked.
Some of the menu lines can be selected, but are without
functions:
Recording is in session; if required, cancel recording session.
Hotel mode switched on; if necessary, switch off hotel mode.
No sound, volume cannot be increased:
Hotel mode was activated with volume too low:
1. Switch off hotel mode.
2. Set the new max. volume level for hotel mode.
3. Switch on hotel mode.
Detailed information is available in the section ’hotel mode’.
Cassette is jammed in the TV-VIDEO Combi:
Don’t use force. Switch off with the 8 power switch for 30
seconds, then switch it on again.
No playback on the TV-Video Combi:
There is no recording on the cassette: Change the cassette.
Poor quality playback on the TV-Video Combi:
The cassette is badly worn or of poor quality: Use a new
cassette.
Tracking is not properly adjusted: Turn to chapter ’PLAYBACK
FUNCTIONS’ and read the section ’Eliminating picture
interference’.
Poor playback of recordings made via the scart socket
EXT :
Recording copy-guarded data via the scart socket EXT can
lead to picture/sound distortions. This is not a fault in your
machine.
The TV-Video Combi will not record:
The TV channel is not stored or not selected properly: Check TV
channels stored.
You have loaded a cassette which is erase protected: Undo the
erase protection on the cassette.
Programmed recording does not work:
You have not set the TIMER properly: Check the TIMER blocks.
Clock/date were set incorrectly: Check clock/date.
You have put in a cassette that is erase protected: Undo the
erase protection on the cassette.
’VPS/PDC’ switched on but ’VPS/PDCtime’ wrong: ’Enter
’VPS/PDCtime exactly to the minute. Have the aerial checked.
The machine has not been switched to standby when recording
starts: Switch machine off in time before recording using the
STANDBY m button.
After a ’programmed recording with Video Plus+’ the programme
number of the TIMER block does not correspond with the desired
programme number:
1. Confirm the PlusCode programming number using the
OK
button.
2. Press the
TIMER k button.
3. Change the programme number displayed in the ’
PROG.
entry field.
4. Confirm with the
TIMER k button.
9. BEFORE YOU CALL AN ENGINEER
24
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips 14PV227 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips 14PV227 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips 14PV227

Philips 14PV227 User Manual - Dutch - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info