492068

Philco TB100HH9 Manual

19
Zoom out
Zoom in
Previous page
1/32
Next page
19
EN
1A23
ADVANCED OPERATION
ADVANCED
OPERATION
4 Select “AUTOSCAN” using [K / L], then
press [OK].
AUTOSCAN
EXIT
CHANNEL
TIME
DETAIL
INITIAL
AUTOSCAN will rescan all channels.
This may take a while to complete.
BACK
AUTOSCAN
AUTOSCAN
The system is now scanning
12% Channel Found
EXIT
• STB starts receiving available digital channels and
stores them in the channel map.
• When the scanning is complete,
“AUTOSCAN COMPLETED” will be indicated.
• After autoscan is complete, press [CH / ] to
verify whether STB is receiving channels
properly.
To cancel during scanning:
Press [SETUP] or [OK].
NOTE:
•
If canceled, some channels not yet scanned may not
be received. We recommend completing autoscan.
• When you want to completely refresh the channel
map, delete all the channels, then do the autoscan
again. See “Adding/Deleting Channels” on page 17
for details.
When “NO SIGNAL” appears on the screen:
Verify the antenna connection, then scan again.
The STB tunes in channel 2-1 and “NO SIGNAL”
appears if the STB could not receive any channels.
Selecting RF OUT Channel
If you want to enjoy analog TV channels also, you
must set the RF out channel.
1 Press [SETUP] to display “SETUP”
menu.
2 Select “CHANNEL” using [K
/ L], then
press [OK].
3 Select “RF OUT” using [K
/ L], then
press [OK].
4 Select the desired setting using [K
/ L],
then press [OK].
Default setting is “CH3”.
Switch RF OUT.
If the screen doesn’t show anything
after switching RF OUT, set the TV
Channel to CH3, then hold down a
“SETUP”button for 3 seconds.
CH3
RF THROUGH
CH4
E.g., switching from CH3/CH4
output to RF THROUGH
Switch RF OUT.
CH3
RF THROUGH
CH4
If the screen doesn’t show anything
after switching RF OUT, then hold
down a “SETUP”button for 3
seconds.
E.g., switching from RF
THROUGH to CH3/CH4 output
• Select “RF THROUGH” if...
- you want to receive and view the analog TV
channels on your TV. (The STB’s power must be
on.) Switch your TV’s channel from the video
input channel (ch3 or ch4) to the analog channel
to view the analog TV channels.
• Select “CH3” or “CH4” if...
- you want to view the digital TV channels output
through the STB on your TV. (You also can
switch between “CH3” and “CH4” by holding
[SETUP] down over 3 seconds.) Then tune your
TV to the corresponding external input channel
(ch3 or ch4). Refer to your TV’s manual for
details.
5 Using [s / B], select “YES” if you like
to proceed. Select “NO” if you want to
cancel. Then, press [OK].
E.g., switching from CH3/CH4
output to RF THROUGH
RF OUT is RF THROUGH
Are you sure ?
YES
NO
If the screen doesn’t show
anything after switching
RF OUT, set the TV Channel
to CH3, then hold down a
“SETUP”button for 3 seconds.
6 Press [SETUP] to exit “SETUP” menu.
NOTE:
•
If the screen doesn’t show anything after making a
selection, tune your TV to ch3 and then switch the
RF out setting by holding down [SETUP] over 3
seconds.
• RF cable connection is required for receiving
analog TV signal. Refer to “Connecting to TV” on
page 10.
• To view analog TV channels through the STB, the
STB must be turned on.
X6032UD_Book.indb 19X6032UD_Book.indb 19 11/28/2007 4:34:40 PM11/28/2007 4:34:40 PM
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philco TB100HH9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philco TB100HH9 in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info