679511

Phicomm FIR151B Manual

39
Zoom out
Zoom in
Previous page
1/49
Next page
FIR151B/300B/302B/303B
Wireless Router
User Manual
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 1 of 49
Contents
Important notes and information
1. About the user manual
1.1 Structure of the user manual
1.2 Used symbols and fonts
1.3 Standard compliance (CE, FCC)
2. Introduction
3. Hardware connections
4. Router configurations
4.1 TCP/IP settings
4.2 Router configurations
4.2.1 Setup wizard
4.2.2 Network settings
4.2.3 Wireless settings
4.2.4 Health and power saving
4.2.5 Running status
4.2.6 System Tools
4.2.7 Wireless advanced settings
4.2.8 Security settings
4.2.9 Parental control
4.2.10 Application
4.2.11 Dynamic DNS
4.2.12 Routing settings
4.2.13 Bandwidth control
4.2.14 IP und MAC binding
4.2.15 Logout
5. Troubleshooting
6. Technical support – contact us
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 2 of 49
LEGAL INFORMATION ABOUT INTELLECTUAL PROPERTY
All company, product and service names mentioned herein are trademarks, registered
trademarks or service marks of their respective owners. Shanghai Feixun
Communication Co., Ltd. reserves the right to revise the content of this document at any
time without prior notice. No part of this document may be reproduced or transmitted
in any form or by any means, electronical or mechanical, including photo-copying,
recording or storing in a retrieval system, or translated into any language in any form
without prior written permission of Shanghai Feixun Communication Co., Ltd.
DISCLAIMER
Any pre-installed software or data provided as a bundle to this device is subject to the
applicable law under the responsibility of the issuing software / service provider. The
hardware manufacturer cannot be held liable for any breach, malfunction or other
occurrence raised by using this third-party software. Only the issuing providers can
lawfully be held responsible. Shanghai Feixun Communication Co., Ltd. does not own the
intellectual property of the third-party software and applications that are delivered with
this product. Therefore, Shanghai Feixun Communication Co., Ltd. will not provide any
warranty of any kind for these third-party software and applications. Neither will
Shanghai Feixun Communication Co., Ltd. provide support to customers who use these
third-party software and applications nor be responsilbe or liable for the functions of
these third-party software and applications. Third-party software and applications
services may be interrupted or terminated at any time. Shanghai Feixun Communication
Co., Ltd. does not guarantee that any content or service would be maintained for any
period during its availability. Third-party service providers provide content and services
through network or transmission tools outside of the control of Shanghai Feixun
Communication Co., Ltd. to the greatest extent permitted by applicable law, it is
explicitly stated that Shanghai Feixun Communication Co., Ltd. shall not compensate or
be liable for services provided by third-party service providers or the interruption or
termination of third-party contents or services. Shanghai Feixun Communication Co.,
Ltd. Shall be not responsible for the legality, quality or any other aspects of any software
installed on this product, or for any uploaded or downloadad third-party works, such as
texts, images, videos or software. Customers shall bear the risk for any and all effects
including incompatibility between the software and this product, which result from
installing software or uploading or downloading the third-party works.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 3 of 49
LIMITATION OF DAMAGES
To the maximum extent permitted by applicable law, in no event shall Shanghai Feixun
Communication Co., Ltd. be liable for any special incidental, indirect or consequential
damages or lost profits, business, revenue, data, goodwill or anticipated savings. The
maximum liability (this limitaion shall not apply to liability for personal injury to the
extent applicable law prohibits such a limitation) of Shanghai Feixun Communication Co.,
Ltd. arising from the use of the product described in this document shall be limited to
the amount paid by customers for the purchase of this product.
IMPORTANT HEALTH INFORMATION AND SAFETY PRECAUTIONS
When using this product, the safety precautions below must be taken to avoid possible
legal liabilities and damages. Retain and follow all product safety and operating
instructions. Observe all warnings in the operating instructions on the product.
To reduce the risk of bodily injury, electric shock, fire and damage to the equipment,
observes the following precautions.
SAFETY PRECAUTIONS FOR PROPER INSTALLATION
CAUTION: Connecting to a weaker inappropriate charger can result in an electric shock
to your device.
SAFETY PRECAUTIONS FOR PROPER SUPPLY UNIT
Use the correct power source!
This product can only be charged with matching standard external power source
appointed by Shanghai Feixun Communication Co., Ltd.
Shanghai Feixun Communication Co., Ltd. is not liable for any device breakdown or
safety accident arising from the use of unauthorized external power source.
PRECAUTION OF HEARING LOSS
GENERAL WARNING: To prevent possible hearing damage,
do not listen at high volume levels for long periods.
Permanent hearing loss may occur if the receiver, headphones, speakerphone or
earpieces are used at high volume. Use only compatible receivers, headphones,
speakerphones or earpieces with your device. Turn on the audio and check the volume
before inserting anything in your ear. You can adapt over time to a higher volume of
sound that may sound normal but can be damaging to your hearing. If you experience
ringing in your ears or muffled speech, stop listening and check your hearing. The louder
the volume, the less time is required before your hearing could be affected.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 4 of 49
Hearing experts suggest that to protect your hearing:
•
Limit the amount of time you use receiver, headphones, speakerphone or earpieces
at high volume.
•
Avoid turning up the volume to block out noisy surroundings.
•
Turn the volume down if you cannot hear people speaking near you.
SAFETY PRECAUTION FOR DIRECT SUNLIGHT
Keep this product away from excessive moisture and extreme temperatures. The device
is designed to be operated in temperatures between 0°C and 40°C. Low- or high-
temperature conditions might cause the device to temporarily stop working properly. Do
not leave the product in a vehicle or in places where the temperature may exceed 70°C
(window sill or behind glass). Avoid dramatic changes in temperature or humidity when
using the device as condensation may form on or within the device.
When you are using the device, it is normal for the device to get warm. The exterior of
the device functions as a cooling surface that transfers heat from inside the unit to the
cooler air outside.
ENVIRONMENT RESTRICTIONS
Do not use this product in gas stations, fuel depots, chemical plants or where blasting
operations are in process, or in potentially explosive atmospheres such as below deck on
boats, fuel or chemical transfer or storage facilities, and areas where the air contains
chemicals or particles, such as grain, dust or metal powders. Please be aware that sparks
in such areas could cause an explosion or fire resulting in bodily injury or even death.
EXPLOSIVE ATMOSPHERES
In any area with a potentially explosive atmosphere or where flammable materials exist,
the product should be turned off and the user should obey all signs and instructions.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or even
death. Users are advised not to use the equipment at refueling areas such as service or
gas stations, and are reminded of the need to observe restrictions on the use or radio
equipment in fuel depots, chemical plants or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often, but not always, clearly marked.
These include fueling areas, below deck on boats, fuel or chemical transfer or storage
facilities, and areas where the air contains chemicals or particles, such as dust or metal
powders.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 5 of 49
SAFETY PRECAUTIONS FOR RADIO FREQUENCY EXPOSURE
•
Avoid using your device near metal structures (e. g. the steel frame of a building).
•
Avoid using the device near strong electromagnetic sources, such as microwave
ovens, sound speakers, TV and radio.
•
Use only original manufacturer-approved accessories.
•
Use of non-original manufacturer-approved accessories may violate your local RF
exposure guidelines and should be avoided.
INTERFERENCES WITH MEDICAL EQUIPMENT FUNCTIONS
This product may cause medical equipment to malfunction. The use of this device is
forbidden in most hospitals and medical clinics.
If you use any other personal medical device, consult the manufacturer of your device to
determine if they are adequately shielded from external RF energy.
HEARING AID DEVICES
Some devices may interfere with some hearing aid devices. In the event of such
interference, you may want to consult your service provider, or call customer service line
to discuss alternatives.
NON-IONIZING RADIATION
Your device has external antennas. This product should be operated in its normal-use
position to ensure the radiative performance and safety of the interference. Users are
advised that for satisfactory operation of the equipment and for the safety of personnel,
it is recommended that no part of the human body be allowed to come too close to the
antenna during operation of the equipment.
Use only the supplied antennas. Use of unauthorized or modified antennas may impair
transfer quality and damage the device, causing loss of performance and SAR levels
exceeding the recommended limits as well as result in noncompliance with local
regulatory requirements in your country.
To assure optimal device performance and ensure human exposure to RF energy is
within the guidelines set forth in the relevant standards, always use your device only its
normal-use position. Contact with the antennas may impair quality and cause your
device to operate at a higher power level than needed. Avoiding contact with the
antenna area when the device is in use optimizes the antenna performance.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 6 of 49
GENERAL PRECAUTIONS
AVOID APPLYING EXCESSIVE PRESSURE TO THE DEVICE
Do not apply excessive pressure on the device to prevent damaging them.
DEVICE IS GETTING WARM AFTER PROLONGED USE
When using your device for prolonged periods the device may become warm. In most
cases this condition is normal and therefore should not be interpreted as a problem with
the device.
HEED SERVICE MARKING
Except as explained in the user manual, do not repair any product yourself. Service
needed on components inside the device should be done by an authorized service outlet
or provider.
PHICOMM is entitled to use new or reconditioned replacements parts or boards for
repairs under warranty, provided they have the same functionality as the parts to be
replaced.
DAMAGE REQUIRING SERVICE
Unplug the device from the electrical outlet and refer servicing to an authorized service
center or provider under the following conditions:
•
Liquid has been spilled or an object has fallen onto the product.
•
The product has to been exposed to rain or water.
•
There are noticeable signs of overheating.
•
The product does not operate normally when you follow the operating instructions.
AVOID HOT AREAS
The product should be placed away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that products heat.
AVOID HOT AREAS
Never use the product in a wet location.
AVOID USING YOUR DEVICE AFTER A DRAMATIC CHANGE IN TEMPERATURE
When you move your device between environments with very different temperature
and/or humidity ranges, condensation may form on or within the device. To avoid
damaging the device, allow sufficient time for the moisture to evaporate before using
the device.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 7 of 49
NOTICE:
When taking the device from low-temperature conditions into a warmer
environment or from high-temperature conditions into a cooler environment, allow the
device to acclimate to room temperature before turning on power.
AVOID PUSHING OBJECTS INTO THE DEVICE
Never push objects of any kind into cabinet slots or other openings in the product. Slots
and openings are provided for ventilation. These openings must not be blocked or
covered.
MOUNTING ACCESSORIES
Do not use the product on an unstable table, cart, tripod or bracket. Any mounting of
the product should follow the manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
AVOID UNSTABLE MOUNTING
Do not place the product with an unstable base.
USE PRODUCT WITH APPROVED EQUIPMENT
This product should be used only with personal computers and options identified as
suitable for use with your equipment.
CLEANING
Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning, but NEVER use water to clean the
device.
The device has been provided with special treatments featuring that it could dispose dirt
and sweat on its surface. The device itself does not have a stain-resistant function. In
case of smudginess and dyeing, please wipe it with clean damp sponge immediately.
Please keep the device dry when necessary.
PACEMAKER
The device may cause disturbance to pacemakers. Please keep the device a
proper distance of least 5 centimeters away from pacemakers.
If you need detailed information about other active implantable medical
devices, please consult your doctor to ensure the magnetic interference of such active
implantable medical devices.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 8 of 49
CAUTION
Update your operating system with caution.
•
Improper operation or unforeseen external factors may cause an operating system
update fails; the device will not work properly. If such a situation occurs, you need
to send the unit in for repair.
•
An unofficial operating system can cause security risks. Please install only official
updates provided by Phicomm, if not you will void the warranty and a repair is
chargeable.
SW-Update
•
During the update process all user data will be erased. Please backup your data
before.
Package contents
Please check the package content before the installation of the router:
1x Wireless Router
1x power supply unit
1x RJ45 cable
1x quick start guide
GPL license and CE declaration
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 9 of 49
Summary of changes
Issue Issue date Remarks
1
September 2014
Initial release
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 10 of 49
1. About the user manual
This user manual includes a complete overview of the configuration and functions of
PHICOMM routers of the FIR series.
1.1 Structure of the user manual
The document is structured as follows:
1.2 Used symbols and fonts
The following symbols are used in the user manual:
DANGER! WARNING!
May result in personal injury
Note
Useful additional information
Chapter
Title Subject
1 About the user manual
Basic description of document content,
definition of symbols and conventions
2 Introduction Description of basic functions
3 Hardware connections
Description of the way connecting the
router with other hardware
4 Wireless router configurations
Description of the router configuration
5 Troubleshooting FAQs and solutions
6 Technical support – contact us
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 11 of 49
The following editorial conventions are used in the manual:
Convention Explanation
Bold Field names / button names are written in bold
Example: click menu View
Italic Commands, screen output, file names and paths are
written in Italic.
Example: Input 192.168.0.1 in IP address text box.
<...>
<...> keyboard or actual names are represented in angle
brackets
Example: Click <Ctrl> + <Alt> + <Delete> to open the
task manager.
> Used for menu sequence
Example: Click File > Print to print.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 12 of 49
1.3 standard compliances (CE, FCC)
Declaration of Conformity
For CE marking in the EU (European Union)
Shanghai Feixun Communication Co., Ltd.
No.3666, Sixian Rd., Songjiang District, Shanghai, P.R.China
We declare under our sole responsibility that our products
Product Name: Wireless Router
Model: FIR151B, FIR300B, FIR302B, FIR303B
to which this declaration relates are in conformity with the following normative
European and international standards:
Safety
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
EN 62311:2008
EMC
EN 301 489-1 V1.9.2(2011-09)
EN 301 489-17 V2.2.1(2012-09)
EN 55022:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 55024:2010
Radio Spectrum
EN 300 328 V1.7.1(2006-10)
By conformance with the standards referenced our products follow the provisions of
the directives listed below.
R&TTE Directive 1999/5/EC
EMC Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
Date: July 8, 2014
Jie Hu
Manager for Product Certification
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 13 of 49
FCC STATEMENT
This device has been tested and complies with Part 15 of the FCC Rules for Class B.
These regulations are intended to protect against adverse effects of device operation
in a home environment.
The operation of a device under FCC regulations Part 15 is subject to the following
two conditions:
•
The device may not cause harmful interference.
•
This device must accept any interference, including all those that cause
undesirable behavior.
This router generates and uses radio signals and therefore may interfere with radio
communications if not installed. However, there can be no guarantee that
interference will not occur. If a communication fault can occur, which can be tested
by simply switching off and on the device, you should perform the following actions:
•
Realign antennas
•
Increase distance of the router to radio or television
•
Use router with a different circuit than the radio or TV operate
•
Contact dealer or manufacturer
Any use not expressly approved by PHICOMM changes to the device will invalidate
the guarantee.
This equipment complies with the FCC RF radiation exposure limits set forth for an
uncontrolled environment. This router and its antenna / antennas must not be
operated in the immediate vicinity of other radio wave emitting devices / antennas.
The antennas used for this router must be at least 20 cm away from people.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 14 of 49
2. Introduction
The routers of the FIR series are all-in-one router for home and SOHO users to share
broadband internet connection over a wired or a wireless network.
The speed of up to 300 Mbps (FIR151B up to 150 Mbps) provides users with
extraordinary smooth internet surfing, internet phone calling and online gaming.
By adopting external Omni-directional antenna(s), the product greatly increases the
wireless range and sensitivity, which enables to receive wireless signals in any corner
of your home or your office.
The routers of the FIR series support the following features:
•
speed up to 300 Mbps (FIR151B up to 150Mbps)
•
backward compatible with 802.11b/g products
•
health and power saving allows parents or administrators to establish restricted
access policies for children or staff
•
WPS button allows easy ON/OFF of the internet connection
•
bandwidth control allows administrators to control the bandwidth for each PC
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 15 of 49
3. Hardware connections
To establish a connection using a modem, please follow the steps 1-1 to 4 of the chart below.
If you use an Ethernet cable, please connect RJ with the WAN port directly (steps 1-2 to 4)
Note
The connections might vary by models.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 16 of 49
4. Wireless router configurations
This section gives instructions of the procedures that must be performed to enable
the wireless router.
After completion of the third point the router is connected with the internet. Please
select the corresponding internet connection on your PC and click connect.
4.1 TCP/IP settings
The IP address has to be obtained automatically before starting the configuration of
the router. Please follow these steps:
1. With the right mouse button please click on the right bottom corner. Click Open
Network and Sharing Center and select Change adapter settings on the upper left of
the screen.
2. Select network connection type and open the Properties. In the Properties window
please double click Internet Protocol Version 4 (TCP/IPv4).
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 17 of 49
3. Select both Obtain an IP address automatically and Obtain DNS server address
automatically. Click OK to confirm the configuration.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 18 of 49
4.2 Router configurations
Open the web browser and enter 192.168.2.1 in the address bar.
Enter Username and Password (preset as admin/admin). You can find this
information also at the bottom of the label on your router. Select the languages on
the right side. Then click the Login button.
After successful login, you will see the page of the Setup Wizard. Enter the needed
settings or click Cancel to leave this page (to see the web management page).
You can find the Setup Wizard in menu on the left. A small HELP button is on the
right side to provide comprehensive instructions.
To confirm the settings on all pages please click Save. By clicking Cancel you always
will return to the former page.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 19 of 49
4.2.1 Setup Wizard
The setup wizard simplifies installation and configuration steps.
Menu item Explanation
Network Settings
WAN protocol PPPoE
PPPoE is typically used for DSL services. Select PPPoE
and type in the Username and Password provided by
your internet service provider. Then click the Save
button.
Dynamic IP (automatically obtain)
Select Automatically obtain (Dynamic IP) if internet
service provider does not provide any IP to use. This
option is commonly used for cable modem services.
Router will obtain IP address information automatically.
Click Save button.
Static IP address
Select Static IP if internet service provider provides the
static IP address, subnet mask, default gateway and DNS
server address. Type in those information and click the
Save button.
Wireless Security
Wireless network name
(SSID)
Define SSID to any other name you prefer or keep it
unchanged.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 20 of 49
Menu item Explanation
Wireless password Set a wireless password (more than 8 characters) to
prevent others from accessing your network without
permission.
Note
The SSID should be changed and no longer match with the name
specified by the manufacturer. Please create an anonymous one as
possible SSID, which does not allow any conclusions about the
location of the router.
4.2.2 Network Settings
Operating mode
Select Router or AP button for operation mode.
Menu item Explanation
Router This is the default and the most commonly used
wireless operating mode. The router connects wired or
wireless with the network / internet.
AP The router acts as a central connection point, which
wireless clients can connect to.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 21 of 49
WAN settings
Select Access Mode Of WAN and WAN Protocol on WAN Settings page. If your
internet service provider is running on a DHCP server, select Dynamic IP as
connection type. The router will automatically get IP parameters from your internet
service provider.
Note
If the WAN port network segment is 192.168.2.X, go to LAN
Settings page to modify LAN IP port to other network segments (for
example 192.168.2.1) to avoid conflicts.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 22 of 49
LAN Settings
Note
If you change the LAN IP address of the router, log in the web
management page with the new IP address.
MAC Clone
Some internet service providers require the registration of your computer’s MAC
address. If you want to clone the MAC address select Enabled.
Menu item Explanation
IP address Enter LAN IP address of the router.
Subnet Mask Enter the subnet mask associated with the LAN IP
address.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 23 of 49
4.2.3 Wireless Settings
There are two submenus under the Wireless Settings menu:
•
Wireless Basic Settings
•
Wireless MAC Filtering
Click any of them to configure the corresponding function.
Wireless Basic Settings
Menu item Explanation
Wireless Basic Settings
Wireless Status Select Enabled or Disabled to control the wireless
function of the router.
SSID Name of the wireless network
Wireless Mode If all wireless devices connected with the wireless router
are in the same transmission mode (for example
802.22b), select 11b Mode.
If the devices use different transmission modes, select
11b/g/n Mode.
SSID Broadcast If you choose Enabled, the wireless router will
broadcast the SSID name.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 24 of 49
Menu item Explanation
Wireless Security Settings
Security Options
Disabled
WEP: Wired Equivalent Privacy
WPA-PSK: Pre-Shared Key of WPA
WPA2-PSK: Pre-Shared Key of WPA2
WPA/WPA2-PSK: automatically based on the wireless
stations’ capacity and request
Note
The security modes are different in the kind of encryption.
WEP encryption provides the least protection while WPA2-PSK is to
overcome the most difficult and therefore offers the best
protection.
Wireless MAC Filtering
Enter the MAC address. Set to block or allow the PC(s) to connect with the wireless
router. To set MAC addresses proceed as follows:
1. Select Enabled under Wireless MAC Filtering.
2. Select Blocked or Allowed under Filter Options.
3.
Fill 00:0A:EB:00:07:5F in Add MAC Address.
4. Click Add/Save button.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 25 of 49
4.2.4 Health and Power Saving
Set to turn on/off the wireless router according to your actual needs (for example
rest times or limit surfing time for children). You can also turn off the power of the
wireless router to save power and protect the environment at the same time.
Note
In order the router is working properly, the router time must be
synchronized with the internet time.
If the router time is different from the internet time, proceed as follows to
synchronize: Click Set at once > synchronize with PC
Now you can configure the time settings:
1. Select WIFI/Reset Combination under Hardware Switch Settings.
2. Select Enabled (default) under Time Switch and adjust the RF power in Power
Adjust according to your demand.
Note
It will impact the performance and the coverage of the wireless.
3. Set time in Time Settings (day, week) and Time Settings (hour) separately.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 26 of 49
4.2.5 Running status
Device Information
This page displays WAN, LAN, Wireless network’s parameters and information about
the router.
There are IP addresses, subnet masks, default gateways, SSID, hardware- and
software-versions etc.
Press Refresh button to refresh the Device Information list.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 27 of 49
DHCP Clients
Menu item Explanation
DHCP Clients
DHCP-Server DHCP server configures the TCP/IP protocol for each PC
in the LAN automatically.
Start IP address 1st address in the IP address pool
End IP address Last address in the IP address pool
DHCP Clients List
Refresh Click the button to refresh the DHCP clients list
Wireless Clients
Click Refresh button to check the wireless clients.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 28 of 49
Traffic Statistics
Check the traffic statistic results and the packet intervals.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 29 of 49
4.2.6 System Tools
Check out different administration tools: System Management, Time Management,
WEB Management, Modify Login Password, System Diagnostics and System Log.
System Management
Menu item Explanation
Factory Reset Restore factory default values
System Restart Restart the router
Software Upgrade Update software
Configuration File
Management
Backup and restore the configuration
Note
All user settings will be deleted when factory reset is enabled.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 30 of 49
Time Management
Set the network time of your system or click Sync with PC to synchronize with the
computer.
Note
You can get GMT time after connecting with the internet.
Web Management
Menu item Explanation
LAN Web Management Restricts LAN access and only allows MAC addresses in
the list to access the Web Management page
Remote Web Management Allows the remote management of the router
Note
If the web management port conflicts with the ports of virtual
server and DMZ entry, when you start the remote management,
the virtual server and DMZ entry will not work.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 31 of 49
Modify Login Password
Manage the details of your account and modify username and password.
Note
Username and password lengths are less than or equal to 16
characters.
System Diagnostics
Ping or Tracert commands to test connectivity between router and other hosts.
Please proceed as follows:
•
Select Ping.
•
Enter IP Address / Domain Name.
•
Enter Number of Ping Packages, Ping Packet Size and Tracert Hops.
•
Click Start.
You will see the results in Diagnostic Results.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 32 of 49
System Log
If you want to set more detailed settings, select Advanced beside the Basic button at
the top of the screen.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 33 of 49
4.2.7 Wireless Advanced Settings
There are WDS Settings, WPS Settings and Wireless Advanced Settings.
WDS Settings
The WDS function can help you to extend the wireless range. It supports Lazy Mode,
Repeater Mode und Bridge Mode.
Menu item Explanation
WDS Mode
Lazy Mode In this mode no further configurations are needed. Click
Save and the connecting client should be in Repeater
Mode or Bridge Mode.
Bridge Mode In this mode you can connect two or more wired
devices wirelessly. You need to add the wireless MAC
address of the connected device into the routers AP
MAC address table or select one from the scanning
table. At the same time the connected device should be
in Lazy, Repeater or Bridge Mode.
Repeater Mode You can select this mode to extend the distance
between two WLAN devices.
It operates as WDS repeater and connects to both –
client card as AP and another AP. In typical repeater
applications APs with WDS function connect to other
APs, which have to support WDS too. In this mode you
need to add the MAC address of the connected device
into the routers AP MAC address table. The connected
client should be in Lazy, Repeater or Bridge Mode.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 34 of 49
Input the MAC address of the other wireless router in MAC address of the wireless
access point.
Note
Two wireless routers must use the same channel, encryption type
and encryption key. If the wireless security mode is one of WPA,
WPA2 and WPA/WPA2, the wireless routers must work with the
same SSID.
WPS settings
The WPS function can help to add a new device to the network quickly. If the client
device supports WPS and is equipped with a WPS button, you can add it to the
network by pressing the WPS button on the device and then press the button of the
router two minutes. The status LED on the router becomes green after five minutes,
if the device has been added to the network successfully. If your client asks for the
router’s PIN number, enter this PIN number into your client device. If your client
device has a WPS Settings PIN number, enter that number into the PIN box.
Menu item Explanation
WPS Settings
WPS (WiFi Protected
Settings)
Establish easy and quick a connection between router
and client device through encrypted contents. The users
only enter the PIN code to configure.
Copyright @ 2014 Phicomm Europe GmbH – print only for private use!
page 38 of 49
4.2.8 Security Settings
Click Firewall to configure.
Firewall
Select Enabled or Disabled to enable or disable the firewall.
If the firewall is enabled, the system refuses all requests from the internet. Only
packets from the LAN which are belonging to defined connections and for which the
status database is created can pass the firewall and can have access to the LAN.
By default the firewall is enabled. To expose all hosts in the LAN to the internet you
can disable the firewall.
Menu item Explanation
Advanced Security Settings
DoS Attack Prevention
Enable for attack prevention.
Open the ICMP-Flood Attack
Filtering
Select to protect against ICMP-FLOOD attacks.
ICMP-Flood Packet
Threshold
If the number of ICMP data packets exceeds the
threshold, the defense measures act immediately.
Open the UDP-Flood Attack
Filtering
Select to protect against UDP-FLOOD attacks.
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Phicomm FIR151B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Phicomm FIR151B in the language / languages: English as an attachment in your email.

The manual is 8,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Phicomm FIR151B

Phicomm FIR151B User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info